Effects of different micro-feature structures on warpage and deformation of light guide plate

JIANG Bing-yan; SHEN Long-jiang; LUO Jian-hua; WENG Can

doi:null

您当前的位置：

首页 >

文章列表页 >

Effects of different micro-feature structures on warpage and deformation of light guide plate

更新时间：2020-08-12

- Effects of different micro-feature structures on warpage and deformation of light guide plate
- Optics and Precision Engineering Vol. 15, Issue 2, Pages: 180-185(2007)
- 作者机构：
  
  中南大学机电工程学院,湖南长沙,410083
- 作者简介：
- 基金信息：
- DOI：
  CLC： TN873.93
- Received：22 September 2006，
  
  Revised：18 December 2006，
  
  Published Online：20 February 2007，
  
  Published：20 February 2007
- 稿件说明：
移动端阅览
JIANG Bing-yan, SHEN Long-jiang, LUO Jian-hua, et al. Effects of different micro-feature structures on warpage and deformation of light guide plate[J]. Optics and precision engineering, 2007, 15(2): 180-185.
DOI：

JIANG Bing-yan, SHEN Long-jiang, LUO Jian-hua, et al. Effects of different micro-feature structures on warpage and deformation of light guide plate[J]. Optics and precision engineering, 2007, 15(2): 180-185. DOI：

摘要

为研究不同微特征结构对导光板翘曲变形的影响

以导光板翘曲变形为质量目标

利用Moldflow MPI5

首次仿真研究了尺寸规格为11×3×0.8的导光板上5种不同微特征结构阵列(V型凹槽阵列、U型凸槽阵列、金字塔阵列、圆环阵列以及微透镜阵列)在不同工艺参数下对导光板翘曲变形的影响。仿真结果表明

微凸点微结构阵列影响最大

微圆凸点阵列导光板最大翘曲量为0.039 7 mm

圆环微结构阵列影响最小

相同工艺参数下圆环微结构阵列导光板最小翘曲量为0.028 2 mm

两者相差最大达40.78%

而且凹结构微特征阵列对导光板翘曲量的影响幅度总是小于凸结构微特征阵列。结论认为

在导光板设计阶段就应考虑不同微结构特征对导光板注射成型翘曲变形的影响并优先选用圆环等凹结构微特征阵列

以减少导光板注射成型的翘曲量。

Abstract

To study the influence of different micro-feature structures on the warpage and deformation of injection molded light guide plate

We applied MoldFlow MPI5.0 to simulate the influence of five different micro-feature structures (micro V groove structure

micro U protrude structure

micro pyramid structure

micro cirque structure and micro lens structure) on the warpage and deformation of light guide plate with 11 mm×3 mm×0.8 mm dimensions for the first time. The results show that the influence of micro lens array structure on the warpage and deformation of the light guide plate is bigger than that of other microfeature structures

the biggest warpage and deformation of micro lens array light guide plate is 0.039 7 mm

and the influence of micro rings array structure is the smallest one. With the same processing parameters

the warpage and deformation of micro rings array light guide plate is 0.028 2 mm

the difference reaches 40.78%

furthermore the influence of convex micro-feature structures is bigger than concave micro-feature structures at all time. It is shown that we should consider the influence of different designs of micro-feature structures on the injection molding of light guide plate in advance

and the preferences are concave micro-feature structures like micro cirque structure.

关键词

Keywords

references

. 陈庆伟,刘正舜. 背光模组技术介绍[J]. 电子与材料杂志,1999,1(1):104-107. CHEN Q W,LIU ZH SH. Introduction of backlight module technology[J].J. Electron & Mater., 1999, 1(1): 104-107.(in Chinese)

. 张增宝,翁志成,丛小杰,等. 液晶背投电视中蝇眼透镜阵列照明系统的设计[J]. 光学精密工程, 2002,10 (2): 126-129. ZHANG Z B,WENG Z C,CONG X J, et al.. Design on a fly lens array illumination system applied in LC rear projective TV[J].Opt. Precision Eng.,2002,10(2):126-129.(in Chinese)

. 段萍. LCD背后光源产业及技术[J]. 国际光电与显示,2002,6:23-26. DUAN P.LCD backlight industry & technology[J].Int. Photoelectron Display,2002,6:23-26. (in Chinese)

. 王信阳. 背光模组用导光板发展课题[J]. 光连双月刊,2003,44(3):41-44. WANG X Y. Light guide plate of backlight module[J].J. Opto-Link Bimonthly,2003,44(3):41-44.(in Chinese)

. 潘重德. 背光模组的技术发展趋势[J]. 电子与材料杂志,2003,17(2):50-54. PAN Z D. Development trend of backlight module[J].J. Electron Mater., 2003,17(2):50-54.(in Chinese)

. 蔡俊钦 .导光板光学设计及制程之最佳化研究 . 国立高雄应用科技大学,2004. TSAI Z Q .Optimization of the optical design and processes condition for light guide plate . National KaoHiung University of Applied Sciences, 2004.(in Chinese)

. SHEN Y.K, WU W Y. Study on numerical simulation and experiment of lightguide plate in injection molding[J]. J. Reinforced Plastics and Composites, 2004, 23(11):1187-1206.

. LI Y Y, CHEE G K, JAMES L, et al.. Experimental investigation and numerical simulation of injection molding with micro-features[J].Polymer Eng. Sci., 2002, 42(5): 871-888.

. 蒋金波,杜雪,李荣彬,等. 用于手机背光模组的轮廓渐变V-槽形自由曲面结构的新颖设计[J]. 液晶与显示,2003, 20(3):178-184. JIANG J B, DU X, LEE R B, et al.. Design of the freeform V-cut optics in the cell phone backlight system[J]. Chin. J. of Liquid Cryst. Displ., 2003, 20(3):178-184.(in Chinese)

. 蒋宗树. 导光板导光设计之研究 . 中国台湾:中原大学,2003. JIANG Z SH. Study on the light guide design in a light guide plate . Chung Yuan Christian University, 2003. (in Chinese)

. 方育斌. LCD背光模组之光学最佳化设计 . 中国台湾: 国立成功大学,2004. FANG Y B. The optimization of optical design for LCD backlight module . National Cheng Kung University, 2003. (in Chinese)

. 勾治践,樊仲维,卢锷,等. 光学塑料透镜注射成型关键技术的研究[J]. 光学精密工程,2000, 8(6):526-531. GOU Z J,FAN Z W,LU E, et al.. Injection molding method for optical plastics lens[J].Opt. Precision Eng.,2000, 8(6):526-531.(in Chinese)

. CHEN X, LAMA Y C, LI D Q. Analysis of thermal residual stress in plastic injection molding[J]. J. Mater. Process. Technol.,2000,101:275-280.

. CHOI D S, IM Y T. Prediction of shrinkage and warpage in consideration of residual stress in integrated simulation of injection molding[J]. Composite Structures,1999, 47: 655-665.

. LI D, ZHOU H. Modeling and simulation of residual stress and warpage in injection moulding . Proc. Inst. Mech. Engrs Part C: J. Mechanical Engineering Science, IMechE,2004:521-530.

Views

411

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of injection molding processing parameters on light guide plate with microsturcture array

Multi-state reliability modeling method for Tianwen-1 high-resolution camera

Occlusion image data generation system

Inverse dynamics modeling of 3-RPS/3n-SPS parallel mechanism with redundant limbs

Simulation tool for complex-engineered micro-optical electromechanical system

Related Author

JIANG Bing-yan

WU Wang-qing

PENG Hua-jian

LUO Jian-hua

Yan WANG

Tianyu SUN

Quanquan LUO

Yang LI

Related Institution

School of Mechanical and Electrical Engineering, Central South University

Space Department III， Changchun Institution of Optics，Fine Mechanics and Physics， Chinese Academy of Sciences

School of Computer & Communication Engineering， University of Science and Technology Beijing

School of Mechanical Engineering, Yan Shan University

Heavy-duty Intelligent Manufacturing Equipment Innovation Center of Hebei Province

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰