Dynamic hysteresis model of piezopositioning stage

ZHANG Dong; ZHANG Cheng-jin; WEI Qiang

doi:null

您当前的位置：

首页 >

文章列表页 >

Dynamic hysteresis model of piezopositioning stage

Article | 更新时间：2020-08-12

- Dynamic hysteresis model of piezopositioning stage
- Optics and Precision Engineering Vol. 17, Issue 3, Pages: 549-556(2009)
- 作者机构：
  
  1. 山东大学控制科学与工程学院,山东济南,250061
  2. 泰山学院物理与电子科学系,山东泰安 271021
- 作者简介：
- 基金信息：
- DOI：
  CLC： TN384;TP271
- Received：16 June 2008，
  
  Revised：23 July 2008，
  
  Published Online：25 March 2009，
  
  Published：25 March 2009
- 稿件说明：
移动端阅览
张栋, 张承进, 魏强. 压电微动工作台的动态迟滞模型[J]. 光学精密工程, 2009,17(3): 549-556

ZHANG Dong, ZHANG Cheng-jin, WEI Qiang. Dynamic hysteresis model of piezopositioning stage[J]. Editorial Office of Optics and Precision Engineering, 2009,17(3): 549-556
张栋, 张承进, 魏强. 压电微动工作台的动态迟滞模型[J]. 光学精密工程, 2009,17(3): 549-556 DOI：

ZHANG Dong, ZHANG Cheng-jin, WEI Qiang. Dynamic hysteresis model of piezopositioning stage[J]. Editorial Office of Optics and Precision Engineering, 2009,17(3): 549-556 DOI：

摘要

为实现压电微动工作台的快速准确运动定位

研究了其运动定位模型。压电工作台的运动定位精度主要受工作台动态特性和迟滞特性的影响

在介绍这两类典型特性模型及其适用范围的基础上

提出了能够同时体现压电工作台动态特性和迟滞特性的动态迟滞模型

并给出了采用Prandtl-Ishlinskii (PI)迟滞算子的动态迟滞模型参数辨识途径。以TRITOR100型压电工作台为例进行实验研究

结果表明:当压电工作台在30 m的定位范围内以900 V/s的输入电压速率进行快速运动定位时

动态迟滞模型的模型精度比以往常用的线性动态模型和迟滞模型有较大提高

其平均误差为0.16 m

最大误差为0.38 m

为高性能运动定位工作台控制系统的设计提供了模型基础。

Abstract

In order to realize dynamic positioning of piezopositioning stage with high speed and high accuracy

the motion positioning model of the stage is studied. Because the dynamic positioning accuracy of piezopositioning stage is affected primarily by dynamic property and hysteresis property of the stage

this paper proposes a dynamic hysteresis model of piezopositioning stage after introducing two kinds of typical property models and their applicable scopes. Furthermore

the parameter identification method of the dynamic hysteresis model constituting of Prandtl-Ishlinskii (PI) hysteresis operator is given. Experimental studies on the TRITOR100 piezopositioning stage indicate that the dynamic hysteresis model is more accurate than both the linear dynamic model and PI hysteresis model when the stage positioning is dynamically positioned at high speed in 900 V/s input voltage within 30 m positioning range. The mean error of the dynamic hysteresis model is 0.16 m

and the maximum error is 0.38 m

which provides foundations for designing high performance control system of piezopositioning stage.

关键词

Keywords

references

刘俊标. 微纳加工中的精密工作台技术[M]. 北京:北京工业大学出版社,2004. LIU J B. Technology of Precision Stage in Micro-nano Fabrication[M]. Beijing: Publishing House of Beijing University of Technology, 2004. (in Chinese)[2] 李庆祥,王东生,李玉和. 现代精密仪器设计[M]. 北京:清华大学出版社,2004. LI Q X, WANG D SH, LI Y H. Design of Modern Precision Instruments[M]. Beijing: Tsinghua University Press, 2004. (in Chinese)[3] 马立,荣伟彬,孙立宁. 三维纳米级微动工作台的设计与分析[J]. 光学精密工程, 2006,14(6):1017-1024. MA L, RONG W B, SUN L N. Design and analysis of a novel 3-DOF nano positioning stage[J]. Opt. Precision Eng., 2006,14(6):1017-1024. (in Chinese)[4] DEVASIA S, ELEFTHERIOU E, MOHEIMANI S O R. A survey of control issues in nanopositioning[J]. IEEE Transactions on Control Systems Technolog, 2007,15(5):802-823.[5] BASHASH S, JALILI N. Robust multiple frequency trajectory tracking control of piezoelectrically driven micro/nanopositioning systems[J]. IEEE Transactions on Control Systems Technology, 2007,15(5):867-878.[6] LEANG K K, DEVASIA S. Feedback-linearized inverse feedforward for creep, hysteresis, and vibration compensation in AFM piezoactuators[J]. IEEE Transactions on Control Systems Technology, 2007,15(5):927-935.[7] 孙立宁,孙绍云,曲东升,等. 基于PZT的微驱动定位系统及控制方法的研究[J]. 光学精密工程, 2004,12(1):55-59. SUN L N, SUN SH Y, QU D SH, et al.. Micro-drive positioning system based on PZT and its control[J]. Opt. Precision Eng., 2004,12(1): 55-59.(in Chinese)[8] 田孝军,王越超,席宁,等. 机器人化纳米操作系统驱动器驱动与探针定位研究[J]. 仪器仪表学报,2007,28(7):1223-1228. TIAN X J, WANG CH Y, Xi N, et al.. Actuator actuating and probe positioning of robotic nanomanipulation[J]. Chinese Journal of Scientific Instrument, 2007,28(7):1223-1228. (in Chinese)[9] 李春涛,谭永红. 迟滞非线性系统的建模与控制[J]. 控制理论与应用,2005,22(2):281-287. LI CH T, TAN Y H. Modeling and control for nonlinear systems with hysteresis . Control Theory and Application, 2005,22(2):281-287. (in Chinese)[10] 魏强,张玉林. 压电陶瓷微位移工作台的建模方法 . 光学精密工程, 2007,15(10):1596-1601. WEI Q, ZHANG Y L. Modeling method of micro-displacement stage driven by piezoelectric ceramic[J]. Opt. Precision Eng., 2007,15(10):1596-1601. (in Chinese)[11] 魏强,张玉林,于欣蕾,等. 扫描隧道显微镜微位移工作台的神经网络PID控制方法研究[J]. 光学精密工程, 2006,14(3):422-427. WEI Q, ZHANG Y L, YU X L, et al.. Study on neural network PID control for micro-displacement stage of Scanning Tunneling Microscope[J]. Opt. Precision Eng.,2006,14(3):422-427. (in Chinese)[12] LIN F J, SHIEH H J, HUANG P K. Adaptive wavelet neural network control with hysteresis estimation for piezo-positioning mechanism[J]. IEEE Transactions on Neural Networks, 2006,17(2):432-444. [13] ADRIAENS H, de KONING W, BANNING R. Modeling piezoelectric actuators . IEEE/ASME Transactions on Mechatronics, 2000,5(4):331-341.[14] ANG W T, GARMN F A, KHOSLA P K, et al.. Modeling rate-dependent hysteresis in piezoelectric actuators . Proceeding of IEEE International conference on intelligent robots and systems, 2003(2):1975-1980.[15] SHIEH H J, HSU C H. An integrator-backstepping-based dynamic surface control method for a two-axis piezoelectric micropositioning stage[J]. IEEE Transactions on Control Systems Technology,2007(5):916-926. [16] KREJCI P, KUHNEN K. Inverse control of system with hysteresis and creep . IEE Proc.Control Theory Appl., 2001,148(3):185-192.[17] GE P, MUSA J. Modeling hysteresis in piezoceramic actuators[J]. Precision Engineering, 1995(1):211-221.[18] KUHNEN K, JANOCHA H. Inverse feedforward controller for complex hysteretic nonlinearities in smart-material systems[J]. Control Intell. Syst., 2001,29:74-83.[19] JANOCHA H, PESOTSKI D, KUHNEN K. FPGA-based compensator of hysteretic actuator nonlinearities for highly dynamic applications[J]. IEEE/ASME Transactions on mechatronics, 2008,13(1):112-116.

Views

1123

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Trajectory tracking control for tri-axial fast tool servo using hybrid electromagnetic-piezoelectric actuation

Identification and control of dynamic modeling for piezoceramic actuator

Related Author

ZHU Zhiyuan

ZHU Zihui

ZHOU Xiaoqin

ZHU Limin

ZHU Zhiwei

CHEN Hui

TAN Yong-hong

ZHOU Xing-peng

Related Institution

School of Mechanical Engineering， Nanjing University of Science and Technology

School of Mechanical and Aerospace Engineering， Jilin University

School of Mechanical and Power Engineering， Shanghai Jiao Tong University

东南大学自动化学院

桂林电子科技大学电子工程与自动化学院

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰