Fabrication and performance analysis of tapered POF connector

ZENG Yong-xi; ZHUANG Qi-ren

doi:null

您当前的位置：

首页 >

文章列表页 >

Fabrication and performance analysis of tapered POF connector

Article | 更新时间：2020-08-12

- Fabrication and performance analysis of tapered POF connector
- Optics and Precision Engineering Vol. 17, Issue 7, Pages: 1535-1541(2009)
- 作者机构：
  
  1. 华侨大学信息科学与工程学院,福建泉州,362021
  2. 泉州师范学院理工学院,福建泉州,362000
- 作者简介：
- 基金信息：
- DOI：
  CLC： TN253
- Received：28 November 2008，
  
  Revised：09 January 2009，
  
  Published Online：25 July 2009，
  
  Published：25 July 2009
- 稿件说明：
移动端阅览
曾永西, 庄其仁. 锥形塑料光纤过渡器的制作及测试[J]. 光学精密工程, 2009,17(7): 1535-1541

ZENG Yong-xi, ZHUANG Qi-ren. Fabrication and performance analysis of tapered POF connector[J]. Editorial Office of Optics and Precision Engineering, 2009,17(7): 1535-1541
曾永西, 庄其仁. 锥形塑料光纤过渡器的制作及测试[J]. 光学精密工程, 2009,17(7): 1535-1541 DOI：

ZENG Yong-xi, ZHUANG Qi-ren. Fabrication and performance analysis of tapered POF connector[J]. Editorial Office of Optics and Precision Engineering, 2009,17(7): 1535-1541 DOI：

摘要

研究了可作为塑料光纤与石英光纤连接器件的锥形塑料光纤过渡器的制作方法及性能测试。采用重力垂直熔融拉锥法制作锥形塑料光纤过渡器

并研究其在实验室条件下的最佳工艺参数。重复实验发现

当加热电压为6.0 V

加热区中心温度在214 ℃附近

拉伸力为1.40 g左右时

塑料光纤的拉伸过程容易控制

拉伸后的塑料光纤表面具有良好的光学质量。测试显示锥形塑料光纤的透射率随着锥度的增大而减小

表面显微形貌良好

出射模式数明显减少

出射模模场强度集中在低阶模部分

可见光透射谱在400~500 nm的损耗加大。对测试结果的分析表明

采用重力垂直熔融拉锥法可以制备性能优良的锥形塑料光纤过渡器

实验得到的最佳工艺参数可为POF连接器、耦合器的实际生产提供参考。

Abstract

Plastic Optical Fiber(POF) tapered connectors can be used as the connection devices of POFs and quartz optical fibers

so this paper introduces the fabrication and performance of tapered POF connectors. A gravity vertical fused elongated taper method is used to fabricate the tapered POF connectors

and the optimal technical parameters are also obtained under the laboratory conditions. It is found that the process of POF stretching is easy to be controlled and the tapered POF connectors show its good optical quality when the control voltage is 6.0 V

the heating zone center temperature is about 214 ℃ and the stretch strength is about 1.40 g. Experiments prove that the transmission rate of the POF with a fine surface morphology decreases with increasing taper angles

its out light modes decreases

the out light mode intensity is on the low rank modes

and the losses from the visible light transmission spectrum increases in the ranges of 400 to 500 nm. These results show that the gravity vertical fused elongated taper is a effective way to fabricate the tapered POF connectors

and the obtained technical parameters from the experiments can provide the references for the actual productions of POF connectors or POF couplers.

关键词

Keywords

references

曾永西,庄其仁,张淑贤. 新一代塑料光纤接入网[J]. 光通信技术,2005,29(7):59-61. ZENG Y X,ZHUANG Q R,ZHANG SH X,et al.. A new generation of POFs optical access network[J]. Optical Communication Technology, 2005, 29(7): 59-61. (in Chinese)[2] MING H X,XING SH,WANG P,et al.. Polymer optical fiber and it's application . Ninth National Opto-electronics Technology and System Conference,Invited Report, 2001,12(2):55-64.[3] KOIKE Y. Giga-island concept realized with high-speed GI plastic optical fiber . Second Asia-Pacific Polymer Fibre Optics Workshop, 2003:4-7.[4] 刘荣华,张宁. 用于塑料光纤接入网的三优先级控制协议设计[J]. 光子学报,2008,37(7):1356-1360. LIU R H,ZHANG N. Design of three priority control protocol applied to plastic optic fiber access network[J]. Acta Photonica Sinica , 2008, 37(7): 1356-1360. (in Chinese)[5] 桂玉屏,徐震,胡先志. 塑料光纤连接的智能家庭光纤通信系统[J]. 光通信研究, 2006(4):44-46. GUI Y P,XU ZH,HU X ZH. Plastic-fiber-connected intelligent home fiber-optic communication systems[J]. Study on Optical Communications , 2006(4):44-46. (in Chinese)[6] 王云明,孙小菡,张明德,等. 塑料光纤锥形过渡器光波传输特性的研究[J]. 东南大学学报(自然科学版),2002,32(3):351-353. WANG Y M,SUN X H,ZHANG M D,et al.. Study on performance of light wave propagation in tapered polymer optical fiber connector[J]. Journal of Southeast Univwrsity(Natural Science Edition), 2002,32(3): 351-353. (in Chinese)[7] 薛春荣,祝生祥,肖志刚. 锥形光纤间的耦合特性[J]. 光子学报,2004,33(7):803-805. XUE CH R,ZHU SH X,XIAO ZH G. Coupling properties between two tapered fiber[J]. Acta Photonica Sinica, 2004,33(7): 803-805. (in Chinese)[8] 连重炎, 杜旭日, 庄其仁,等. 锥形塑料光纤光束准直特性的研究[J]. 光纤与电缆及其应用技术,2008(2):33-36. LIAN CH Y,DU X R,ZHUANG Q R,et al.. Study on the characterization of beam collimation in tapered plastic optical fiber[J]. Optical Fiber & Electric Cable and Their Applications, 2008(2):33-36. (in Chinese)[9] 许强,黄肇明,黄勇. 26熔融拉锥型单模光纤耦合器的特性分析[J]. 光学学报,2005,25(6):751-754. XU Q,HUANG ZH M,HUANG Y. Analysis of coupling power for fused-biconical 26 single-mode optical fiber coupler[J]. Acta Optica Sinica,2005,25(6):751-754. (in Chinese)[10] 林小莉,李平,王强,等. 熔锥型光纤耦合器的扭转响应[J]. 光子学报,2004,33(5):540-543. LIN X L,LI P,WANG Q, et al.. Twist response of fused-tapered fiber coupler[J]. Acta Photonica Sinica,2004,33(5):540-543. (in Chinese)[11] 刘丽飒,张磊,蔡志平. CO2激光熔拉锥过程光功率控制研究[J]. 光学精密工程,2006,14(3):368-373. LIU L S,ZHANG L,CAI ZH P. CO2 laser fabrication of biconical-tapered fiber and its laser power controlling[J]. Opt. Precision Eng., 2006, 14(3):368-373 . (in Chinese)[12] 陈新桥,林如俭,代康. 塑料光纤耦合器制备方法探讨[J]. 光纤与电缆及其应用技术,2005(2):5-9. CHEN X Q,LIN R J,DAI K. Fabrication of POF couplers[J]. Optical Fiber & Electric Cable and Their Applications,2005(2):5-9. (in Chinese)[13] 曾永西,庄其仁,张淑贤,等. 聚合物光纤热预拉锥工艺实验研究[J]. 激光与红外,2006,36(8):691-693. ZENG Y X,ZHUANG Q R,ZHANG SH X,et al.. Technical experiment of POF thermal pre-elongated taper[J]. Laster & Infrared, 2006, 36(8): 691-693. (in Chinese)[14] 帅词俊,段吉安,钟掘. 熔锥型光纤耦合器流变成形的工艺敏感性研究[J]. 光学精密工程,2005,13(1):40-46. SHUAI C J, DUAN J A,ZHONG J. Technical sensitiveness in the rheological manufacture progress of fused taper coupler[J]. Opt. Precision Eng., 2005, 13(1): 40-46. (in Chinese)[15] 孙圣和,王廷云,徐影.光纤测量与传感技术[M]. 哈尔滨:哈尔滨工业大学出版社,2002:3-4. SUN SH H,WANG Y Y,XU Y. Optical Measurement and Sensing Technology [M]. Harbin: Harbin Institute of Technology Press, 2002: 3-4. (in Chinese)

Views

551

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰