Application of zero clearance support method based on circle mirrors

SHA Wei; ZHANG Xing-xiang; CHEN Chang-zheng; Xu Yan-jun; Ren Jian-yue

doi:10.3788/OPE.20101810.2199

您当前的位置：

首页 >

文章列表页 >

Application of zero clearance support method based on circle mirrors

Article | 更新时间：2020-08-12

- Application of zero clearance support method based on circle mirrors
- Optics and Precision Engineering Vol. 18, Issue 10, Pages: 2199-2205(2010)
- 作者机构：
  
  1. 中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
  2. 中国科学院研究生院,北京 100039
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20101810.2199
  CLC： TP73;TH703
- Received：01 December 2009，
  
  Revised：04 February 2010，
  
  Published Online：28 October 2010，
  
  Published：20 October 2010
- 稿件说明：
移动端阅览
沙巍, 张星祥, 陈长征, 许艳军, 任建岳. 圆形反射镜无隙支撑方法的应用[J]. 光学精密工程, 2010,18(10): 2199-2205

SHA Wei, ZHANG Xing-xiang, CHEN Chang-zheng, Xu Yan-jun, Ren Jian-yue. Application of zero clearance support method based on circle mirrors[J]. Editorial Office of Optics and Precision Engineering , 2010,18(10): 2199-2205
沙巍, 张星祥, 陈长征, 许艳军, 任建岳. 圆形反射镜无隙支撑方法的应用[J]. 光学精密工程, 2010,18(10): 2199-2205 DOI： 10.3788/OPE.20101810.2199.

SHA Wei, ZHANG Xing-xiang, CHEN Chang-zheng, Xu Yan-jun, Ren Jian-yue. Application of zero clearance support method based on circle mirrors[J]. Editorial Office of Optics and Precision Engineering , 2010,18(10): 2199-2205 DOI： 10.3788/OPE.20101810.2199.

摘要

针对空间光学遥感器圆形反射镜在安装过程中会由于采用间隙配合胶接方法在温度变化时产生非对称应力从而引起非对称像差(主要表现为像散)

以及使用的胶层为非线性材料使反射镜面形变化不可逆从而降低结构可靠性等问题

提出了基于过盈配合的无隙支撑方法。该方法依据最小势能原理

使用柔性块以过盈配合的方式固定反射镜。采取线性搜索方法分析得到了适当的过盈量(0.03 mm)

利用有限元方法模拟实际工况

得到镜面面形变化情况。对反射镜组件进行温度循环试验

并利用干涉仪对反射镜进行检测。试验显示

温度变化4 ℃时

镜面面形RMS值最大为0.018

符合设计要求(RMS值0.02)

干涉图表明反射镜受力均匀、无像散;在温度循环试验中

反射镜面形变化可逆。这些结果表明

对于圆反射镜

采用无隙支撑方法能够很好地解决温度变化对镜面面形的不利影响。

Abstract

In the secondary mirror mounting procedure of a space-borne remote sensor

the method of clearance fixation with auxiliary adhesive is used to fix the mirror usually

which will cause the asymmetric aberration and influence on the imaging quality when the temperature is changed. Moreover

variation of the surface shape is irreversible due to the adhesive layer come from nonlinear materials. To improve the imaging quality and structure reliability

this paper proposed a zero clearance support method based on the lowest potential energy principle . Via the method of interference fixation with flexible blocks

the astigmatism aroused by non-symmetrical stress was avoided theoretically

and the irreversible problem was solved. The appropriate interference value (0.03 mm) was obtained by the finite element analysis. By using the interference value

both gravity and temperature variation(4 ℃) were considered and the surface shape test was performed using an interferometer. Experiments show that the RMS value of the surface shape is 0.018

which meets the design requirements (RMS value0.02). obtained results demonstrate that the zero clearance support method for the circle mirrors can relieve the adverse effect of the surface shape caused by temperature variation.

关键词

Keywords

references

黄本诚,马有礼. 航天器空间环境试验技术 [M]. 北京: 国防工业出版社, 2002:39-42. HUANG B C, MA Y L. Space Environment Test Technology of Spacecraft [M]. Beijing: National Defense Industry Press, 2002:39-42. (in Chinese)[2] 张志杰,袁怡宝. 单边导角形柔性铰链的计算与性能分析 [J]. 光学精密工程,2007,15(3):384-389. ZHANG Z J, YUAN Y B. Design calculation and analysis of half corner-filleted flexure hinge [J]. Opt. Precision Eng., 2007,15(3):384-389. (in Chinese)[3] 齐迎春,金光,许艳军. 空间薄膜反射镜面形设计及优化 [J]. 光学精密工程,2007,15(6):818-823. QI Y C, JIN G, XU Y J. Design and optimization for shape of space membrane mirror [J]. Opt. Precision Eng., 2007,15(6):818-823. (in Chinese)[4] 陈连. 基于可靠性优化技术的计算和选择过盈配合的新方法 [J]. 机械强度, 2003,25(5):519-522. CHEN L. New method to calculate and choose interference fit based on the reliability and optimization technology [J]. Journal of Mechanical Strength, 2003,25(5):519-522. (in Chinese)[5] PAULI PEDERSEN. On shrink fit analysis and design [J]. Comput Mech, 2006,37:121-130.[6] KOVACS A. Thermal stresses in a shrink fit due to an inhomogeneous temperature distribution [J]. Acta Mechanica, 1994,105:173-187[7] 魏延刚,宋亚昕,李建,等. 过盈配合接触边缘效应与应力集中 [J]. 大连铁道学院学报, 2003,24(3):4-8. WEI Y G, SONG Y X, LI J, et al.. Study of stress concentration and edge-effect of interference fit joints [J]. Journal of Dalian Jiaotong University, 2003,24(3):4-8. (in Chinese)[8] 王栋,杨洪波,陈长征. 光学表面面形的计算机仿真 [J]. 计算机仿真, 2007,24 (2):298-301. WANG D, YANG H B, CHEN C Z. Computer simulation of the optical surface [J]. Computer Simulation, 2007,24(2):298-301. (in Chinese)[9] KULCHYTSKY-ZHYHAILO R D,OLESIAK Z S,YEVTUSHENKO O O. On thermal contact of two axially symmetric elastic solids [J]. Journal of Elasticity, 2001,63:1-17.

Views

471

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Interference fitted metal-composite material flywheel rotor

Related Author

TANG Ji-qiang1

ZHANG Yong-bin1

ZHAO Li-bin3

Related Institution

北京航空航天大学惯性技术重点实验室

北京航空航天大学新型惯性仪表与导航技术国防重点学科实验室

北京航空航天大学宇航学院

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰