U-bending process of T2 copper foil

WANG Chun-ju; GUO Bin; SHAN De-bin

doi:10.3788/OPE.20101812.2610

您当前的位置：

首页 >

文章列表页 >

U-bending process of T2 copper foil

Article | 更新时间：2020-08-12

- U-bending process of T2 copper foil
- Optics and Precision Engineering Vol. 18, Issue 12, Pages: 2610-2615(2010)
- 作者机构：
  
  哈尔滨工业大学材料科学与工程学院,黑龙江哈尔滨 150001
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20101812.2610
  CLC： TG306
- Received：05 March 2010，
  
  Revised：28 May 2010，
  
  Published Online：25 December 2010，
  
  Published：25 December 2010
- 稿件说明：
移动端阅览
王春举, 郭斌, 单德彬. T2紫铜箔材的U型弯曲变形[J]. 光学精密工程, 2010,18(12): 2610-2615

WANG Chun-ju, GUO Bin, SHAN De-bin. U-bending process of T2 copper foil[J]. Editorial Office of Optics and Precision Engineering, 2010,18(12): 2610-2615
王春举, 郭斌, 单德彬. T2紫铜箔材的U型弯曲变形[J]. 光学精密工程, 2010,18(12): 2610-2615 DOI： 10.3788/OPE.20101812.2610.

WANG Chun-ju, GUO Bin, SHAN De-bin. U-bending process of T2 copper foil[J]. Editorial Office of Optics and Precision Engineering, 2010,18(12): 2610-2615 DOI： 10.3788/OPE.20101812.2610.

摘要

设计了箔板U型弯曲试验方案

使用不同凹模槽宽尺寸和圆角半径的微型模具

在三思微型试验机上完成了试验

分析了模具几何尺寸、箔板厚度等对箔板U型弯曲变形中冲头载荷、回弹以及表面质量的影响。研究结果表明

槽宽尺寸或圆角半径减小时

最大冲头载荷显著增加

且冲头载荷上升和下降速率都明显增大;对比两种不同厚度箔板的冲头载荷显示

冲头载荷减小速率明显快于横截面面积的减小速率

说明产生了明显的尺寸效应;另外

圆角半径或板厚减小

导致回弹角度增大

成形件精度降低;虽然成形件表面比较平整

但侧面出现划痕提示需要提高模具表面质量和采取润滑措施。以上研究结果对指导箔板微成形工艺设计具有重要意义。

Abstract

A U-bending test was designed by using a micro female mold with different groove widths and corner radii on a micro extension tester made by SANS company. The effects of the mold dimension and foil thickness on the maximum punch load

springback and surface quality were analyzed during the micro U-bending process. The results indicate that the reductions of groove width or radius leads to the increases of maximum punch load and the rates of increasing or decreasing of punch load increase greatly.By comparison of the punch loads of foils with different thicknesses

it is shown that the decreasing rate of punch load is larger than that of cross section area

and the size effect occurs obviously. Furthermore

the springback angle increases with the decreasing of thickness or radius

which reduces the accuracy of microparts. As the scratch appears at the side surface of a micro bending part

it suggests that the surface quality of the mold should be improved and the lubricating should be taken. The results have an important significance on the design of foil microforming process.

关键词

Keywords

references

GEIGER M, kLEINER M, ECKSTEIN R. Microforming[J]. Annals of the CIRP. 2001,50(2):445-462.[2] GEIGER M, MERKLEIN M, TOLAZZI M. Metal forming ensures innovation and future in Europe .Proceeding of the 8th International Conference on Technology of Plasticity.Verona, Italy, 2005.[3] VOLLERTSEN F, HU Z, SCHULZE NIEHOFF H,et al.. State of the art in micro forming and investigations into micro deep drawing [J]. Journal of Materials Processing Technology. 2004,151:70-79.[4] VOLLERTSEN F, SCHULZE NIEHOFF H, HU Z. State of the art in micro forming . Proceeding of the 1st ICNFT, Harbin,2004:17-28.[5] SAOTOME Y, YASUDA K, KAGA H. Microdeep Drawability of very Thin Sheet Steels [J]. Journal of Material Processing Technology,2001,113:641-647.[6] ECKSTEIN R, GEIGER M, ENGEL U. Specific characteristics of micro sheet metal working .Proceeding of the 7th International Conference on Sheet Metal, Erlangen, German, 1999, 27-28:529-536.[7] RAULEA L V, GOIJERTS A M, GOVAERT L E, et al.. Size effects in the processing of thin metal sheet [J]. Journal of Materials Processing Technology. 2001,115:44-48.[8] ECKSTEIN R, ENGEL U. Behavior of the grain structure in micro sheet metal working .Proceeding of the 8th International Conference on Metal Forming, 2000:453-459.[9] KOCANDA A, PREJS T. The effect of miniaturization on the final geometry of the bend product // Proceeding of the 8th International Conference on Metal Forming, Krakow, Poland, 2000:375-378.[10] STOLKEN, EVANS. A microbend test method for measuring the plasticity length scale [J]. Acta Mater. 1998,46(14):5109-5115.[11] GAU J T, PRINCIPE C, YU M. Springback behavior of brass in micro sheet forming [J]. Journal of Materials Processing Technology. 2007,(191):7-10.

Views

652

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Precise compression and setting round by mold for large pipes

Related Author

YIN Jing

ZHAO Jun

SUN Hong-lei

ZHAN Pei-pei

Related Institution

Institute of Mechanical Engineering, Yanshan University

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰