Analysis and experiment on millisecond pulsed laser drilling of metals

QIN Yuan; BI Juan; NI Xiao-wu; SHEN Zhong-hua; ZHANG Xi-he

doi:10.3788/OPE.20111902.0340

您当前的位置：

首页 >

文章列表页 >

Analysis and experiment on millisecond pulsed laser drilling of metals

Article | 更新时间：2020-08-12

- Analysis and experiment on millisecond pulsed laser drilling of metals
- Optics and Precision Engineering Vol. 19, Issue 2, Pages: 340-347(2011)
- 作者机构：
  
  1. 南京理工大学理学院信息物理与工程系,江苏南京 210094
  2. 长春理工大学理学院,吉林长春 130022
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20111902.0340
  CLC： TG665
- Received：08 October 2010，
  
  Revised：31 October 2010，
  
  Published Online：22 February 2011，
  
  Published：22 February 2011
- 稿件说明：
移动端阅览
秦渊, 毕娟, 倪晓武, 沈中华, 张喜和. 毫秒激光金属打孔的解析和实验[J]. 光学精密工程, 2011,19(2): 340-347

QIN Yuan, BI Juan, NI Xiao-wu, SHEN Zhong-hua, ZHANG Xi-he. Analysis and experiment on millisecond pulsed laser drilling of metals[J]. Editorial Office of Optics and Precision Engineering, 2011,19(2): 340-347
秦渊, 毕娟, 倪晓武, 沈中华, 张喜和. 毫秒激光金属打孔的解析和实验[J]. 光学精密工程, 2011,19(2): 340-347 DOI： 10.3788/OPE.20111902.0340.

QIN Yuan, BI Juan, NI Xiao-wu, SHEN Zhong-hua, ZHANG Xi-he. Analysis and experiment on millisecond pulsed laser drilling of metals[J]. Editorial Office of Optics and Precision Engineering, 2011,19(2): 340-347 DOI： 10.3788/OPE.20111902.0340.

摘要

研究了用毫秒脉宽的长脉冲激光单个脉冲打深孔的成形过程和打孔速率。首先

由切割法得到了1 ms脉宽的Nd∶YAG高斯激光对厚铝板打孔时孔的形貌

激光能量为7.9和28.9 J时

对应的孔深分别为1.849和2.975 mm。根据实验建立了轴对称模型

通过热传导方程得到了固相温度的解析解。然后

假设物质一旦熔融就离开孔

由能量平衡原理得到了孔形状的表达式。实验发现随激光能量增加

孔深增加

计算与实验结果差异也增大;进一步的计算显示

在其他条件不变时

光束半径的变化对孔深的影响较大。因此

引入离焦效应对算法进行了改进

改进后的计算结果与实验总体相符。最后

研究了长脉冲激光对铝、铜、银和钛4种金属的打孔速率

结果表明

钛对激光吸收最强、热传导率能力最弱

打孔速率最大。

Abstract

With the purpose of investigating the millimeter order hole's formation and the drilling speed drilled by a single millisecond pulse laser

the shapes of holes in an aluminium slab drilled by a Nd: YAG Gaussian laser with 1 ms pulse width were obtained with the cutting method in an experiment. The hole depth is 1.849 mm and 2.975 mm when the laser energy is 7.9 J and 28.9 J

respectively. A semi-infinite axisymmetric model was established according to the experiment and the analytical solution of temperature in a solid phase was derived based on the thermal conduction equation. Meanwhile

by assuming that material was removed from the hole once it was melted

the function describing the hole's shape was obtained with the energy balance theory. It was found that the difference between the calculation and the experimental results becomes larger as well as the hole's depth increases with the increase of laser energy. Further investigation indicates that the variation of beam radius affects the hole's depth greatly under other unaltered conditions. Thus

the defocusing effect was induced to modify the analytical solution and obtained results are in agreemeat well with those of the experiments. Finally

the drilling speed of millisecond pulsed laser for aluminum

copper

silver and titanium were studied. The results show that drilling speed for titanium is the fastest one due to its high absorptivity for laser and poor heat conduction ability.

关键词

Keywords

references

KAYULOV S V, GUSEV A A, ZAICHIKOV E G, et al.. Drilling of narrow holes in metals by millisecond pulses of Nd∶YAG lasers [J]. Laser Physics, 1998,8(2):527-531.[2] BOSTANJOGLO G, SARADY I, BECK TH, et al.. Processing of Ni-based aero engine components with repetitively Q-switched Nd∶YAG-lasers [J]. SPIE, 1996,2789:145-157.[3] YEO C Y, TAM S C, JANA S, et al.. A technical review of the laser drilling of aerospace materials [J]. Journal of Materials Processing Technology, 1994,42(1):15-49.[4] YANG J, ZHAO Y, ZHU X. Transition between nonthermal and thermal ablation of metallic targets under the strike of high-fluence ultrashort laser pulses [J]. Applied Physics Letters, 2006,88:094101-1-3.[5] TUNNA L,O'NEILL W, KHAN A, et al.. Analysis of laser micro drilled holes through aluminium for micro-manufacturing applications [J]. Optics and Lasers in Engineering, 2005,43(9):937-950.[6] SCHNEIDER M, MULLER M,FABBRO R, et al.. Study of hole properties in percussion regime with a new analysis method [J]. JLMN-Journal of Laser Micro/Nanoengineering, 2007,2(2):128-132.[7] YUAN C J, ZHAI H C, WANG X L, et al.. Lensless digital holography with short-coherence light source for three-dimensional surface contouring of reflecting micro-object[J]. Optics Communications, 2007,270(2):176-179.[8] YILBAS B S, MANSOOR S B. Laser pulse heating and phase changes in the irradiated region: temperature-dependent thermal properties case [J]. International Journal of Thermal Sciences, 2009,48(4):761-772.[9] PARK K W, NA S J. Theoretical investigations on multiple-reflection and Rayleigh absorption-emission-scattering effects in laser drilling [J]. Applied Surface Science, 2009,256(8):2392-2399.[10] SAMANT A N, DAHOTRE N B. Computational predictions in single-dimensional laser machining of alumina [J]. International Journal of Machine Tools and Manufacture, 2008,48(12-13):1345-1353.[11] NG G K L, CROUSE P L, LI L. An analytical model for laser drilling incorporating effects of exothermic reaction, pulse width and hole geometry [J]. International Journal of Heat and Mass Transfer, 2006,49(7-8):1358-1374.[12] 穆景阳,万红,白书欣. 长脉冲激光辐照下环氧树脂的热烧蚀规律[J]. 强激光与粒子束,2008,1(1):36-40. MU J Y, WAN H, BAI SH X. Thermal ablation law of cured epoxy under long pulse laser irradiation [J]. High Power Laser and Particle Beams, 2008,1(1):36-40. (in Chinese)[13] 蒋艳锋,江东,钟鸣,等. 长脉冲激光对金属材料热破坏的分析[J]. 激光杂志,2006,27(2):75-76. JIANG Y F, JIANG D, ZHONG M, et al.. Theoretical research: the thermal damage of metal materials, under millisecond-pulsed laser irradiations [J]. Laser Journal, 2006,27(2):75-76. (in Chinese)[14] ZHOU Y C. Reverse bulging and plugging in metal foil induced by high power laser [J]. Journal of Materials Science Letters, 2003,22(1):83-86.[15] BOLEY C D, CUTTER K P, FOCHS S N, et al.. Interaction of a high-power laser beam with metal sheets [J]. Journal of Applied Physics, 2010,107:043016-1-5.[16] 吴东江,马广义,周秋菊,等. 长脉宽脉冲激光硅片弯曲成形试验[J]. 光学精密工程,2007,15(9):1361-1365. WU D J, MA G Y, ZHOU Q J, et al.. Experimental study of bending silicon chip with long pulse width laser[J]. Opt. Precision Eng., 2007,15(9):1361-1365. (in Chinese)[17] ALLMEN M V. 激光束与材料相互作用的物理原理及应用[M]. 北京:科学出版社,1994. ALLMEN M V. Laser-beam Interactions with Materials Physical Principles and Applications [M]. Beijing: Science Press, 1994. (in Chinese)[18] CHAN C L, MAZUMDER J. One-dimensional stead-state model for damage by vaporization and liquid expulsion due to laser-material interaction [J]. Journal of Applied Physics, 1987,62(11):4579-4586.[19] SEMAK V, MASUNAWA A. The role of recoil pressure in energy balance during laser materials processing [J]. Journal of Physics D:Applied Physics, 1997,30(18):2541-2552.[20] QIN Y,CHEN Y B, NI X W, et al.. Axisymmetric numerical simulation of plastic damage in aluminum alloy induced by long pulsed laser[J]. Optics and Lasers in Engineering, 2010,48(3):361-367.[21] SHEN Z H,ZHANG S Y, LU J, et al.. Mathematical modeling of laser induced heating and melting in solids [J]. Optics & Laser Technology, 2001,33(8):533-537.[22] PELIGRAD A A, ZHOU E, MORTON D, et al.. A melt depth prediction model for quality of laser surface glazing of inhomogeneous materials [J]. Optics & Laser Technology, 2001,33(1):7-13.[23] SALONITIS K,STOURNARAS A,TSOUKANTAS G, et al.. A theoretical and experimental investigation on limitations of pulsed laser drilling [J]. Journal of Material Processing Technology, 2007,183(1):96-103.[24] SOLANA P, KAPADIA P, DOWDEN J, et al.. Time dependent ablation and liquid ejection processes during the laser drilling of metals [J]. Optics Communications, 2001,191(1-2):97-112.

Views

383

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Experiment of long pulse high energy laser drilling on silica glass

Related Author

DAI Gang

LU Jian

LIU Jian

ZHANG Liang

NI Xiao-wu

Related Institution

Department of Applied Physics, Nanjing University of Science and Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰