Burst pressure of capillary burst valve based on glass and PDMS

DU Xin; ZHANG Ping; LIU Yong-shun; WU Yi-hui

doi:10.3788/OPE.20111908.1852

您当前的位置：

首页 >

文章列表页 >

Burst pressure of capillary burst valve based on glass and PDMS

Article | 更新时间：2020-08-12

- Burst pressure of capillary burst valve based on glass and PDMS
- Optics and Precision Engineering Vol. 19, Issue 8, Pages: 1852-1858(2011)
- 作者机构：
  
  1. 中国科学院长春光学精密机械与物理研究所应用光学国家重点实验室,吉林长春,130033
  2. 中国科学院研究生院,北京 100039
  3. 长春理工大学机电工程学院,吉林长春,130022
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20111908.1852
  CLC： TH138.52;TQ022.1
- Received：26 September 2010，
  
  Revised：11 January 2011，
  
  Published Online：25 August 2011，
  
  Published：25 August 2011
- 稿件说明：
移动端阅览
杜新, 张平, 刘永顺, 吴一辉. 基于PDMS和玻璃材料的毛细管被动阀临界压力分析[J]. 光学精密工程, 2011,19(8): 1852-1858

DU Xin, ZHANG Ping, LIU Yong-shun, WU Yi-hui. Burst pressure of capillary burst valve based on glass and PDMS[J]. Editorial Office of Optics and Precision Engineering, 2011,19(8): 1852-1858
杜新, 张平, 刘永顺, 吴一辉. 基于PDMS和玻璃材料的毛细管被动阀临界压力分析[J]. 光学精密工程, 2011,19(8): 1852-1858 DOI： 10.3788/OPE.20111908.1852.

DU Xin, ZHANG Ping, LIU Yong-shun, WU Yi-hui. Burst pressure of capillary burst valve based on glass and PDMS[J]. Editorial Office of Optics and Precision Engineering, 2011,19(8): 1852-1858 DOI： 10.3788/OPE.20111908.1852.

摘要

针对现有的数值仿真方法不能够准确地计算矩形截面毛细阀用亲水性很好的玻璃作盖板时的临界压力

提出了一种分析复合壁面毛细管被动阀临界压力的方法。使用Surface Evolver(SE)自由软件

通过设置和实际流动相符的边界条件

并监测在扩张段入口处接触角的变化范围

实现了对由玻璃盖板和PDMS微通道构成的被动阀的临界压力的计算。此时

接触线应该设置为可以进入到扩张段的侧壁上

而不能固定在扩张段入口处。对于深度为25 m

宽深比为2

16的毛细管被动阀

得到的临界压力分别为0.77

0.45

0.33

0.24 kPa。仿真结果和转台实验结果基本相符

证实了SE方法的有效性。文中分析了接触角对毛细阀有效性的影响

指出当通道和平板材料的接触角之和大于90时

毛细阀才能控制流动。

Abstract

As the current simulation methods for capillary burst valves can not exactly calculate the burst pressure when the passive valve is limited by a glass flat cover with good hydrophilicity

a method to analyze the critical pressure of the passive value was proposed. The Surface Evolver (SE) was used to simulate the burst pressure of the microvalve composed of a glass cover and PDMS microchannels by setting the properly boundary conditions and monitoring the variation of the contact angle at the entrance of expansion section.In simulation

the liquid contact line should be set up the entrance of expansion section and come into the expansionary walls that connect the glass cover. Experiments show that the capillary burst pressures are 0.77

0.45

0.33 and 0.24 kPa

respectively

for the microvalves with the depth of 25 m and the aspect of 2

8 and 16. The obtained simulation data are well in agreement with that obtained by a rotating platform. The effect of the contact angle for the capillary burst valve was also discussed

which points out that the valves do work until the sum of the contact angles on both the flat cover and the channel wall is greater than 90.

关键词

Keywords

references

DUCRE J, HAEBERLE S, LUTZ S, et al.. The centrifugal microfluidic Bio-Disk platform[J]. Micromech. Microeng., 2007,17 (7):103-115.[2] SIEGRIST J,GORKIN R,CLIME L, et al.. Serial siphon valving for centrifugal microfluidic platforms[J]. Microfluid Nanofluid., 2010,9(1):55-33.[3] GLI`ERE A, DELATTRE C. Modeling and fabrication of capillary stop valves for planar microfluidic systems[J]. Sens. Actuators A: Phys., 2006,130-131: 601-608.[4] MAN P F, MASTRANGELO C H, BURNS M A, et al.. Microfabricated capillary driven stop valves and sample injector, in: MEMS Conference, Heidelberg, Germany, January 25-29, 1998.[5] LEU T S, CHANG P Y. Pressure barrier of capillary stop valves in micro sample separators[J]. Sens. Actuators A: Phys.,2004,115(2-3): 508-515.[6] CHEN J M, HIANG P C, LIN M G. Analysis and experiment of capillary valves for microfluidics on a rotating disk[J]. Microfluid Nanofluid, 2008,4(5):427-437.[7] CHO H, KIM H Y, KANG J Y, et al.. How the capillary burst microvalve works[J]. J. Colloid Interface Sci.,2007,306(2):379-385.[8] ZENG J, BANERJEE D, DESHPANDE M, et al.. Design analysis of capillary burst valves in centrifugal microfluidics . Micro Total Analysis Systems 2000, Enschede :Kluwer Academic Publishers, 2000:579-582.[9] BRAKKE K A. The surface evolver, Version 2.30. http://www.susqu.edu/brakke/. January 1, 2008.[10] 王毅,常小庆. 微重力环境下推进剂贮箱中三维气液平衡界面的数值模拟[J]. 火箭推进, 2007,33(3):31-35. WANG Y, CHANG X Q. Numerical simulation of three-dimensional gas-liquid equilibrium interfaces in the propellant tank under microgravitycondition[J]. Journal of Rocket Propulsion, 2007,33(3):31-35.(in Chinese)[11] BONN D, EGGERS J, INDERKEU J, et al.. Wetting and spreading[J]. Reviews of modern physics, 2009,81(2):739-805.[12] CONCUS P, FINN R. On capillary free surfaces in the absence of gravity[J]. Acta. Math., 1974,132(1):177-198.[13] 张平, 胡亮红, 刘永顺. 主辅通道型微混合器的设计和制作[J]. 光学精密工程, 2010, 18 (4):872-879. ZHANG P, HU L H, LIU Y S. Design and fabrication of micromixer with main-assist channels[J]. Opt. Precision Eng., 2010,18(4):872-879. (in Chinese)[14] WEISLOGEL M M, LICHTER S. Capillary flow in an interior corner[J]. J. Fluid Mech., 1998,373(1):349-378.[15] SEEMANN R, BRINKMANN M, KRAMER E J, et al.. Wetting morphologies at microstructured surface[J]. Proc. Natl. Acad. Sci., 2005,102(6):1848-52.[16] ZIMMERMANN M, HUNZIKER P, DELMAR-CHE E. Valves for autonomous capillary systems[J]. Microfluid Nanofluid., 2008,5(3):395-402.

Views

358

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Performance optimization of chaotic flow micromixer

Fluidic transportation of open microchannels with a hydrophobic mesh

Fabrication of In-line Micropipettes and Digital Micro-jetting Experiment

Development of Hot Rheologic Deformation Puller for Fabricating Vitreous Three-way Microchannels

Related Author

He ZHANG

Shuang YANG

Rongyan CHUAI

Xin LI

MA Zeng-shuai

YE Xiong-ying

SHANG Yuan-fang

DU Min

Related Institution

College of Information Science and Engineering， Shenyang University of Technology

State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instruments, Tsinghua University

南京理工大学

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰