High precision measurement of taper for taper gauge by optical interference method

KANG Yan-hui; ZHANG Heng

doi:10.3788/OPE.20111911.2551

您当前的位置：

首页 >

文章列表页 >

High precision measurement of taper for taper gauge by optical interference method

Article | 更新时间：2020-08-12

- High precision measurement of taper for taper gauge by optical interference method
- Optics and Precision Engineering Vol. 19, Issue 11, Pages: 2551-2557(2011)
- 作者机构：
  
  中国计量科学研究院北京,100013
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20111911.2551
  CLC： TB922;TH744.3
- Received：28 March 2011，
  
  Revised：17 May 2011，
  
  Published Online：25 November 2011，
  
  Published：25 November 2011
- 稿件说明：
移动端阅览
康岩辉, 张恒. 圆锥量规锥度的高精度光学干涉法测量[J]. 光学精密工程, 2011,19(11): 2551-2557

KANG Yan-hui, ZHANG Heng. High precision measurement of taper for taper gauge by optical interference method[J]. Editorial Office of Optics and Precision Engineering, 2011,19(11): 2551-2557
康岩辉, 张恒. 圆锥量规锥度的高精度光学干涉法测量[J]. 光学精密工程, 2011,19(11): 2551-2557 DOI： 10.3788/OPE.20111911.2551.

KANG Yan-hui, ZHANG Heng. High precision measurement of taper for taper gauge by optical interference method[J]. Editorial Office of Optics and Precision Engineering, 2011,19(11): 2551-2557 DOI： 10.3788/OPE.20111911.2551.

摘要

针对超精密数控机床对圆锥量规锥度高精度测量的需求

研究了一种将"大数"和"小数"相结合

准确测量圆锥量规锥度的方法。介绍了锥度测量系统的基本原理及组成

给出了实验测量结果

分析了测量系统的不确定度。该测量方法利用最大分度间隔误差为0.10的多齿分度台构成高准确度分度系统保证测量"大数"部分的准确性

采用激光偏振干涉装置及精密回转工作台组成小角度测量系统保证测量"小数"部分的精度

而双光束白光干涉系统实现了测量位置的精确定位。实验和分析结果表明

该方法在不确定度置信因子

为2时

锥度测量系统的扩展不确定度约为0.24

优于0.3

可实现圆锥量规任意锥度的高精度测量。

Abstract

For ultra-precision Numerical Control (NC) machine tools in advanced manufacturing industry

a high precision measuring method for the taper of a taper gauge was proposed by combining the integral and fractional parts together. The primary principle and the composition of the system were described

and the experimental measurement of a taper gauge was implemented. Moreover

the measurement uncertainty of the system was analyzed. In this method

the high precision indexing system containing a multi-tooth indexing table with an accuracy of 0.10 was used to ensure the precision and reliability of the integral part

and the laser polarization interference device and a precision rotary table was combined into an angle measuring system to accurately measure the fractional part. Then

the dual-beam white light interference system was used for an accurate positioning. The experiment and analysis results indicate that the measurement uncertainty can be less than 0.3 when the uncertainty confidence level (

) is 2. The method can realize the high precision taper measurement for any taper gauges.

关键词

Keywords

references

中华人民共和国国家质量监督检验检疫总局. GB/T 11853-2003莫氏与公制圆锥量规 [S]. 北京:中国标准出版社,2004. General Administration of Quality Supervision, Inspection and Quarantine of P.R.C.. GB/T 11853-2003Gauges of Morse tapers and metric tapers[S]. Beijing: Stands Press of China, 2004.(in Chinese)[2] 中华人民共和国国家质量监督检验检疫总局. JJG 177-2003圆锥量规 [S]. 北京:中国计量出版社,2003. General Administration of Quality Supervision, Inspection and Quarantine of P.R.C.. JJG 177-2003Taper Gauges[S]. Beijing: China Metrology Publishing House, 2003. (in Chinese)[3] ISO. ISO 12164-1: 2001Hollow taper interface with flange contact surface-Part 1: Shanks-Dimensions[S]. Geneva: International Organization for Standardization, 2001.[4] DIN. DIN 69063-1: 2008-03Machine tools-Tool receiver for hollow taper shanks-Part 1: For Type A and Type C according to DIN 69893, connecting dimensions[S]. Berlin: German Institute for Standardization , 2008.[5] 殷纯永. 现代干涉测量技术[M]. 天津:天津大学出版社,1999. YIN CH Y. Modern Interferometric Measuring Technique[M]. Tianjin: Tianjin University Press, 1999. (in Chinese)[6] 刘雯, 沈妮, 李天初. 用多齿分度台标定激光小角度干涉仪[J] . 计量学报, 2004, 25(4): 298-301. LIU W, SHEN N, LI T CH. Calibration of small-angle laser interferometer by means of multi-teeth table[J]. Acta Metrologica Sinica, 2004, 25(4): 298-301. (in Chinese)[7] 熊文卓, 孔智勇, 张炜. 光电轴角编码器光电信号正交性偏差的相量校正方法[J]. 光学精密工程, 2007, 15(11): 1745-1748. XIONG W ZH, KONG ZH Y, ZHANG W. Phase correction of quartering deviation of photoelectric rotary encoder[J]. Opt. Precision Eng, 2007, 15(11): 1745-1748. (in Chinese)[8] 陈洪芳, 钟志, 丁雪梅. 激光外差干涉的非线性误差补偿[J]. 光学精密工程, 2010, 18(5): 1043-1047. CHEN H F, ZHONG ZH, DING X M. Compensation of nonlinear errors in laser heterodyne interferometers[J]. Opt. Precision Eng, 2010, 18(5): 1043-1047. (in Chinese)[9] WANG L D, WANG J X, XING W L, et al.. Laser interferometer with isolator function[J]. Opt. Precision Eng., 2004, 12(5): 465-470.[10] WYANT J C. White light interferometry[J]. SPIE, 2002, 4737: 98-107.[11] 张以谟, 井文才, 张红霞等. 数字化白光扫描干涉仪的研究[J] . 光学精密工程, 2004, 12(6): 560-565. ZHANG Y M, JING W C, ZHANG H X, et al.. Computerized white light scanning interferometer and the application[J]. Opt. Precision Eng., 2004, 12(6): 560-565. (in Chinese)[12] 舒阳, 邱易, 羡一民. 激光角度干涉仪测量精度的几个影响因素[J] . 工具技术, 2008, 42(5): 72-74. SHU Y, QIU Y, XIAN Y M. Influence factors on measuring precision of laser angular interferometer[J]. Tool Engineering, 2008, 42(5): 72-74. (in Chinese)[13] 王贵甫, 陈桂林, 陈雨良. 激光干涉仪数字测角的新方法及其应用[J]. 光学精密工程, 2001, 9(1): 85-88. WANG G F, CHEN G L, CHEN Y L. A new digital angle measurement technology by using Malchlson interferometer and its application[J]. Opt. Precision Eng., 2001, 9(1): 85-88. (in Chinese)

Views

310

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰