Application of UV-LIGA technology to machining micro-injection mold cavity of cell culture device

MA Ya-Li; LIU Wen-kai; LIU Chong; DU Li-qun

doi:10.3788/OPE.20132105.1228

您当前的位置：

首页 >

文章列表页 >

Application of UV-LIGA technology to machining micro-injection mold cavity of cell culture device

更新时间：2020-08-12

- Application of UV-LIGA technology to machining micro-injection mold cavity of cell culture device
- Optics and Precision Engineering Vol. 21, Issue 5, Pages: 1228-1233(2013)
- 作者机构：
  
  军事交通学院军事物流系2. 大连理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20132105.1228
  CLC： Q.337;TN305.7
- Received：03 December 2012，
  
  Revised：11 January 2013，
  
  Published Online：24 May 2013，
  
  Published：15 May 2013
- 稿件说明：
移动端阅览
马雅丽刘文开刘冲杜立群. UV-LIGA技术在制作细胞培养器微注塑模具型腔中的应用[J]. 光学精密工程, 2013,21(5): 1228-1233

MA Ya-Li LIU Wen-kai LIU Chong DU Li-qun. Application of UV-LIGA technology to machining micro-injection mold cavity of cell culture device[J]. Editorial Office of Optics and Precision Engineering, 2013,21(5): 1228-1233
马雅丽刘文开刘冲杜立群. UV-LIGA技术在制作细胞培养器微注塑模具型腔中的应用[J]. 光学精密工程, 2013,21(5): 1228-1233 DOI： 10.3788/OPE.20132105.1228.

MA Ya-Li LIU Wen-kai LIU Chong DU Li-qun. Application of UV-LIGA technology to machining micro-injection mold cavity of cell culture device[J]. Editorial Office of Optics and Precision Engineering, 2013,21(5): 1228-1233 DOI： 10.3788/OPE.20132105.1228.

摘要

研究了细胞培养器微注塑模具型腔的制作方法。针对微注塑模具型腔的结构特点，采用UV-LIGA套刻技术，分别通过两次SU-8胶光刻和Ni的微细电铸制作了以合金钢为基底的微结构；然后利用掩膜腐蚀方法在铸层上腐蚀出微排气通道。对SU-8厚胶工艺过程中的溶胀现象、匀胶不平整和去除困难等问题进行分析，提出在掩膜板图形四周增设封闭的宽度为20 m的隔离带来减少图形四周SU-8厚胶体积，改善了该处胶模的热溶胀变形，使铸层的尺寸误差由原来的35 m降低到10 m，300 m高的微柱体侧壁陡直。隔离带的引入有效地提高了铸层图形的尺寸和形状精度。由于采用了刮胶的匀胶工艺和发烟硫酸去除SU-8胶的方法，消除了边缘水珠效应，彻底去除了SU-8胶。采用提出的方法可获得铸层质量好，与基底结合强度高的微注塑模具型腔。

Abstract

A fabrication method of micro-injection mold cavity for a cell culture device was explored in this paper. Based on the structural characteristics of the micro-injection mold cavity and overlay UV-LIGA technology

a microstructure using appropriate alloy steel as the substrate was fabricated through SU-8 photoresist optical lithography and micro-electroforming technology respectively twice. Then

a micro exhaust duct was etched on an electroforming deposit through mask etching technology. Meanwhile

the swelling problem of SU-8 thick photoresist

poor surface evenness through spin-coating and SU-8 photoresist removal in the experiment process were analyzed

and a method of designing and fabricating a 20 m wide closed isolation strip around the mask graphics was presented to reduce the volume of SU-8 thick photoresist around the graphics and to improve the swelling deformation of plating mold. By which

the dimension error of the electroforming deposit is from 35 m down to 10 m and 300 m high micro-square-cylinder side wall is steep. The introduction of closed isolation strip improves the dimensional and shape precisions of nickel electroforming deposit effectively and the uses of scraping photoresist and oleum techniques eliminates the edge bead effect and removes SU-8 photoresist completely. As a result

the microinjection mold cavity with good quality and the high bonding strength between substrate and nickel electroforming deposit is obtained successfully.

关键词

Keywords

references

SHEN S C, PAN C T, WANG Y R, et al.. Fabrication of integrated nozzle plates for inkjet print head using microinjection process [J]．Sensors and Actuators A, 2006，127，241-247. [2]VOLKER P, ERIC G, STEFAN G, et al.. Micro-injection moulding for the manufacturing of medical devices [J]. Medical Device Manufacturing & Technology, 2006，25-27. [3]徐征,王继章,杨铎,等. 辅助溶剂对PMMA微流控芯片模内键合的影响[J]. 光学精密工程, 2012, 20(2): 321-328.XU ZH, WANG J ZH, YANG D, et al.. Effect of assistant solvent on in-mold bonding of PMMA microfluidic chips [J]. Opt. Precision Eng., 2012, 20(2): 321-328. (in Chinese)[4]赵兴海,鲍景富,杜亦佳,等. MEMS技术在THz无源器件中的应用[J]. 传感器与微系统，2011，30（7）：5-9.ZHAO X H, BAO J F, DU Y J, et al.. Application of MEMS technology in passive THz-device[J]. Transducer and Microsystem Technologies, 2011，30（7）：5-9. (in Chinese)[5]代俊,石庚辰.基于LIGA工艺的微齿轮误差特点[J]. 探测与控制学报，2010，32(4): 59-64.DAI J, SHI G CH．Study on micro-gears' error of LIGA processing [J]. Journal of Detection＆Control, 2010，32（4）：59-64 .(in Chinese)[6]杜立群,莫顺培,张余升,等. UV- LIGA和微细电火花加工技术组合制作三维金属微结构[J]. 光学精密工程，2010，18(2): 363-368.DU L Q, MO SH P, ZHANG Y SH, et al.. Fabrication of 3D metal microstructure based on UV-LIGA and micro-EDM technology [J]. Opt. Precision Eng., 2010，18（2）：363-368.(in Chinese)[7]胡洋洋,朱荻,李寒松,等．UV-LIGA与微细电火花加工组合制造微细电解阵列电极[J]. 东南大学学报(自然科学版)，2010，40(1): 106-110.HU Y Y, ZHU D, LI H S, et al.. Fabrication of micro-ECM electrode array by combining UV- LIGA with micro electro-discharge machining[J]. Journal of Southeast University(Natural Science Edition), 2010，40（1）：106-110.(in Chinese)[8]RUZZU A, MATTHIS B. Swelling of PMMA-structures in aqueous solutions and room temperature Ni-electroforming [J]. Microsystem Technologies，2002，8，116-119. [9]杜立群，朱神渺，喻立川，等．后烘温度对SU-8光刻胶热溶胀性及内应力的影响[J]. 光学精密工程, 2008，16（3）：500-504.DU L Q, ZHU SH M, YU L CH, et al.. Effect of post exposure bake temperature on thermal swelling of SU-8 photoresist[J]．Opt. Precision Eng., 2008，16（3）：500-504. (in Chinese)[10]崔峰，靖向萌，赵小林，等. SU-8 胶模去除技术[J]. 微细加工技术，2007，（1）：1-6.CUI F, JING X M, ZHAO X L, et al.. Techniques for remove of SU-8 photoresist mold [J]. Microfabrication Technology，2007，（1）：1-6. (in Chinese)

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Design of optical film for ultra-thin MiniLED backlight modules

Design of micro-structure film for improving viewing brightness of vehicle head-up display

Design of optical brightness enhancement film for direct-lit backlight in automobile head-up display

Design and process of ultra-precision drum roll lathe

Investigation on microstructures and interfaces of NiC/Ti neutron multilayers

Related Author

Guo-qiang LÜ

Biao ZHU

Ling YANG

Hui-li XIAO

Qi-bin FENG

Zi WANG

Qi-bin FENG

Li-ye XU

Related Institution

Special Display and Imaging Technology Innovation Center of Anhui Province National Engineering Laboratory of Special Display Technology， Academy of Photoelectric Technology， Hefei University of Technology

School of Electronic Science &Applied Physics， Hefei University of Technology

School of Instrumentation and Opto-Electronics Engineering，Hefei University of Technology

AVIC Hua Dong Photoelectric Co. Ltd.

National Engineering Lab of Special Display Technology， National Key Lab of Advanced Display Technology， Academy of Photoelectric Technology， Hefei University of Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰