Calculation of removal function of ion beam figuring and polishing experiment

TANG Wa; DENG Wei-jie; ZHENG Li-gong; ZHANG Xue-jun

doi:10.3788/OPE.20152301.0031

您当前的位置：

首页 >

文章列表页 >

Calculation of removal function of ion beam figuring and polishing experiment

更新时间：2020-08-13

- Calculation of removal function of ion beam figuring and polishing experiment
- Optics and Precision Engineering Vol. 23, Issue 1, Pages: 31-39(2015)
- 作者机构：
  
  1. 中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
  2. 中国科学院大学北京,中国,100049
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20152301.0031
  CLC： TN305.2
- Received：26 February 2014，
  
  Revised：31 March 2014，
  
  Published：25 January 2015
- 稿件说明：
移动端阅览
唐瓦, 邓伟杰, 郑立功等. 离子束抛光去除函数计算与抛光实验[J]. 光学精密工程, 2015,23(1): 31-39

TANG Wa, DENG Wei-jie, ZHENG Li-gong etc. Calculation of removal function of ion beam figuring and polishing experiment[J]. Editorial Office of Optics and Precision Engineering, 2015,23(1): 31-39
唐瓦, 邓伟杰, 郑立功等. 离子束抛光去除函数计算与抛光实验[J]. 光学精密工程, 2015,23(1): 31-39 DOI： 10.3788/OPE.20152301.0031.

TANG Wa, DENG Wei-jie, ZHENG Li-gong etc. Calculation of removal function of ion beam figuring and polishing experiment[J]. Editorial Office of Optics and Precision Engineering, 2015,23(1): 31-39 DOI： 10.3788/OPE.20152301.0031.

摘要

由于传统的离子抛光工艺采用的确定去除函数的方法操作复杂且成本很高

本文提出了利用法拉第杯对离子束流空间分布进行测量、标定的方法

并计算得到不同离子源工作参数对应的去除函数.首先

基于离子束抛光材料去除原理

研究了离子束抛光过程中束流分布与能量对去除函数的影响

并提出简化的离子束抛光去除函数模型.然后

设计实验并得出离子束流空间分布与去除函数相关参数间的关系

计算得到了不同离子源工作参数产生的离子束流对应的去除函数.对硅和融石英玻璃的相关实验表明:利用法拉第杯扫描结果计算相同材料的去除函数的单位时间体积去除率与实际测量值误差小于2%.结合抛光实验

对

800 mm碳化硅表面硅改性层平面镜进行抛光

得到的初始面形误差均方根(RMS)值为57.886 nm

两次抛光后RMS值为11.837 nm

收敛率达到4.89

满足精密光学加工对去除函数的确定性及精度的要求

并大大提升了确定去除函数的效率.

Abstract

As the method to get the removal function by traditional Ion Beam Figuring (IBF) has complicated operation and higher costs

this paper proposes a new method to calculate the removal function. The method uses the Faraday cup scan to measure and calibrate the temporal distribution of ion beams and to obtain the different working parameters of ion sources which corresponds to removal functions. Firstly

the material removal theory of IBF was studied based on the Sigmund sputtering theory

and the influence of ion beam distribution on the removal function was researched. A simplified IBF removal function model was proposed. Then

an experiment was conducted to obtain the relationship between the temporal distribution of ion beam and the related parameter of removal function

and the different removal functions of various working parameters were calculated with the combination of the basic removal experiment and Faraday cup scan results. Experiments were performed on silicon and fused silica

and the experimental results show that the peak value of the removal function for the same material is proportional to the that of the scan result. A mirror with a

800 mm silicon flat modification layer was polished

obtained the Root Mean Square(RMS) of surface error is 57.866 nm. After polishing for two times

the RMS is 11.837 nm

and the convergence rate is up to 4.89. These results meet the requirements of optical fabrication for polishing accuracy and improve the determining efficiency for removal functions.

关键词

Keywords

references

ALLEN L N. Progress in ion figuring large optics.Laser-Induced Damage in Optical Materials: 1994 International Society for Optics and Photonics, 1995: 237-247.

DEMMLER M, ZEUNER M, LUCA A, et al.. Ion beam figuring of silicon aspheres [J].SPIE, 2011,7934: 793416-793416-6.

GREENLEAF A H. Computer-controlled optical surfacing[C].1980 Technical Symposium East. International Society for Optics and Photonics, 1980: 41-55.

康健, 宣斌, 谢京江. 表面改性碳化硅基底反射镜加工技术现状 [J]. 中国光学, 2013,6(6): 824-833. KANG J, XUAN B, XIE J J.Manufacture technology status of surface modified silicon carbide mirrors [J]. Chinese Optics, 2013,6(6): 824-833.(in Chinese)

王旭. 使用优化的固着磨料磨盘全口径加工碳化硅反射镜 [J]. 光学精密工程, 2012, 20(10): 2123-2131. WANG X. Fabrication of SiC mirror in full aperture with optimized fixed abrasive polishing pad [J]. Opt. Precision Eng., 2012, 20(10): 2123-2131.(in Chinese)

张峰. 非球面碳化硅表面硅改性层的数控化学机械抛光 [J]. 光学精密工程, 2013, 21(12):3015-3020. ZANG F. Computer-controlled chemical mechanical polishing of silicon modification layer on aspheric silicon carbide surface [J]. Opt. Precision Eng., 2013, 21(12):3015-3020.(in Chinese)

李锐钢, 郑立功, 张峰, 等. 大口径高陡度离轴非球面精磨阶段的数控加工 [J]. 光学精密工程, 2007, 15(5): 633-639. LI R G, ZHENG L G, ZHANG F, et al.. Computer controlled manufacturing during fine grinding stage of highly steep off-axis asphere with large aperture [J]. Opt. Precision Eng., 2007,15(5):633-639.(in Chinese)

CSAHOK Z, FARKAS Z, MENYHARD M, et al.. Surface morphology development during ion sputtering: roughening or smoothing? [J]. Surface Science, 1996, 364(2): L600-L604.

HAENSEL T, NICKEL A, SCHINDLER A. Ion beam figuring of strongly curved surfaces with a (x, y, z) linear three-axes system[C].Optical Fabrication and Testing, Optical Society of America, 2008.

GHIM Y S, YOU S J, RHEE H G, et al.. Ultra-precision surface polishing using ion beam figuring[C].6th International Symposium on Advanced Optical Manufacturing and Testing Technologies (AOMATT 2012), International Society for Optics and Photonics, 2012: 84161O-84161O-4.

LIAO W, DAI Y, XIE X, et al.. Corrective capability analysis and machining error control in ion beam figuring of high-precision optical mirrors [J]. Optical Engineering, 2012, 51(3): 033402-1-8.

廖文林, 戴一帆, 周林, 等. 离子束抛光加工矩形离轴非球面镜 [J]. 国防科技大学学报, 2011, 33(1):100-104. LIAO W L, DAI Y F, ZHOU L, et al.. Ion beam figuring for rectangular off-axis aspheric mirrors [J]. Journal of National University of Defense Technology, 2011, 33(1): 100-104.(in Chinese)

SIGMUND P. Elements of Sputtering Theory [M]. 2009.

MAKEEV M A, CUERNO R, BARABÁSI A L. Morphology of ion-sputtered surfaces [J]. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 2002, 197(3): 185-227.

SIGMUND P. Sputtering by Ion Bombardment Theoretical Concepts [M]. Berlin:Springer Berlin Heidelberg, 1981.

BROWN K L, TAUTFEST G W. Faraday-cup monitors for high-energy electron beams [J]. Review of Scientific Instruments, 1956, 27(9): 696-702.

Views

972

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Ion beam polishing process parameters optimization and polishing experiment of ZnS

Correction of removal function of ion beam figuring highly steep off-axis asphere

Modeling of removal function and optimization of process parameters for robotic polishing M-ZnS

Five-axis CNC machining method for eyeglass lens edge profile

Factors influencing surface figure of optical elements in full-aperture continuous polishing and their control

Related Author

CAI Gen

ZHU Beibei

QIN Lin

ZHANG Chupeng

CHEN Xiao

TANG Wa

DENG Wei-jie

LI Rui-gang

Related Institution

Key Laboratory of Modern Manufacturing Quality Engineering in Hubei Province， Hubei University of Technology

Shanghai Aerospace Control Technology Institute

School of Mechanical Engineering， Hubei University of Technology

Shanghai Aerospace Control Technology Research Institute

School of Mechanical Science and Engineering， Huazhong University of Science and Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰