ZHAO Zhen-qing, YE Dong, WU Bin etc. Point wise distortion correction algorithm with vanishing point collinear constraint[J]. Editorial Office of Optics and Precision Engineering, 2015,23(4): 1196-1204
ZHAO Zhen-qing, YE Dong, WU Bin etc. Point wise distortion correction algorithm with vanishing point collinear constraint[J]. Editorial Office of Optics and Precision Engineering, 2015,23(4): 1196-1204 DOI: 10.3788/OPE.20152304.1196.
Point wise distortion correction algorithm with vanishing point collinear constraint
Point wise correction algorithms are researched and analyzed. The correction accuracy of a point wise distortion correction algorithm based on four-point collinear cross ratio invariability is investigated. It points out that the initial used image points which contain errors will cause the accuracy change in the calculation of other image points. Then
it gives the selection method for image point locations and relative distances when the calculation error is smaller. Based on the above
this paper proposes a point wise distortion correction algorithm based on vanishing point collinear constraint. The algorithm uses vanishing points to improve the linear fit accuracy and the collinear feature to constrain the corrected distortion accuracy. It not only optimizes the image point errors of the distortion correction algorithm based on a four-point collinear cross ratio invariance
but also the initial image point errors
so that the accuracy of distortion correction of all image points is improved ultimately. The simulation based on MATLAB shows that the maximum error of corrected image points is 29.05 times that of the initial image point noise for four million pixels. In contrast to the physical image using the cross ratios from the correction algorithms based on four-point collinear invariant cross ratio and vanishing point collinear constraint as well the uncorrected image
it indicates that the performance of proposed algorithm is better than that of the algorithm based on four-point collinear cross ratio invariance.
关键词
Keywords
references
ZHANG Z Y. A flexible new technique for camera calibration [J]. IEEE Transactions on Pattern Analysis and Machine Intelligence, 2000, 22(11): 1330-1334.
刘书桂, 姜珍珠, 董英华, 等. 采用移动光靶标的分区域相机标定[J]. 光学精密工程, 2014, 22(2): 259-265. LIU SH G, JIANG ZH ZH, DONG Y H, et al.. Sub-regional camera calibration based on moving light target [J]. Opt. Precision Eng., 2014, 22(2): 259-265.
薛俊鹏苏显渝. 基于两个正交一维物体的单幅图像相机标定[J]. 光学学报, 2012, 32(1): 0115001. XUE J P, SU X Y.Camera calibration with single image based on two orthogonal one-dimensional objects[J]. Acta Optica Sinica, 2012, 32(1): 0115001.
贺俊吉, 张广军, 杨宪铭. 基于交比不变性的镜头畸变参数标定方法[J]. 仪器仪表学报, 2004, 25(5): 597-599. HE J J, ZHANG G J, YANG X M. Approach for calibraton of lens distortion based on cross ration invariability[J].Chinese Journal of Scientific Instrument, 2004, 25(5): 597-599
唐巍, 叶东, 袁锋, 等. 视觉测量系统中一种独立的畸变校正算法[J]. 光电子·激光, 2013, 24(2): 308-315. TANG W, YE D, YUAN F, et al.. Independent distortion correction algorithm in vision measurement [J]. Journal of Optoelectronics·Laser, 2013, 24(2): 308-315.
周富强, 胡坤, 张广军. 基于共线特征点的摄像机镜头畸变校正[J]. 机械工程学报, 2006, 42(9):174-177. ZHOU F Q, HU K, ZHANG G J. Correcting distortion of camera lens with collinear points [J]. Chinese Journal of Mechanical Engineering, 2006, 42(9):174-177.
周富强, 蔡斐华. 基于非量测畸变校正的摄像机标定方法[J]. 机械工程学报, 2009, 45(8): 228-232. ZHOU F Q, CAI F H. Camera calibration method based on non-metric distortion correction [J]. Chinese Journal of Mechanical Engineering, 2009, 45(8): 228-232.
张靖, 朱大勇, 张志勇. 摄像机镜头畸变的一种非量测校正方法[J]. 光学学报, 2008, 28(8):1552-1557. ZHANG J, ZHU D Y, ZHANG ZH Y. Non-metric calibration of camera lens distortion [J]. Acta Optica Sinica, 2008, 28(8):1552-1557.
张之江, 车仁生, 黄庆成, 等. 测头成像视觉坐标测量系统中特征点成像中心获取[J]. 光学精密工程, 1998, 6(5): 12-18. ZHANG ZH J, CHEN R SH, HUANG Q CH, et al.. Centroid of characteristic point image obtain in probe imaging vision coordinate measuring system [J]. Opt. Precision Eng., 1998, 6(5): 12-18.
杨博文, 张丽艳, 叶南, 等. 装配位姿视觉检测系统中红外靶点质心定位[J]. 中国机械工程, 2014, 25(7): 965-971. YANG B W, ZHANG L Y, YE N, et al.. Centroid location algorithms of infrared target in computer-vision-based assembly pose detection system [J]. China Mechanical Engineering, 2014, 25(7):965-971.
冯新星, 张丽艳, 叶南, 等. 二维高斯分布光斑中心快速提取算法研究[J]. 光学学报, 2012, 32(5): 0512002. FENG X X, ZHANG L Y, YE N. Fast algorithms on center location of two dimensional Gaussian distribution spot [J]. Acta Optica Sinica, 2012, 32(5): 0512002.
黄风山, 钱惠芬. 三坐标测量机驱动的摄像机标定技术[J]. 光学精密工程, 2010, 18(4): 952-957. HUANG F SH, QIAN H F. Camera calibration technology driven by three-coordinate measuring machine [J]. Opt. Precision Eng., 2010, 18(4): 952-957.
HARTLEY R I, ZISSERMAN A. Multiple View Geometry in Computer Vision[M]. Cambridge:Cambridge University Press, 2000:568-582.