Design and alignment of support structure for off-axis multi-mirror system

MEI Gui; ZHAI Yan; MIAO Jian-yu; PU Qian-shuai

doi:10.3788/OPE.20152308.2280

您当前的位置：

首页 >

文章列表页 >

Design and alignment of support structure for off-axis multi-mirror system

更新时间：2020-08-12

- Design and alignment of support structure for off-axis multi-mirror system
- Optics and Precision Engineering Vol. 23, Issue 8, Pages: 2280-2287(2015)
- 作者机构：
  
  中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20152308.2280
  CLC： V447.3;TH703
- Received：27 March 2014，
  
  Revised：09 April 2014，
  
  Published：25 August 2015
- 稿件说明：
移动端阅览
梅贵, 翟岩, 苗健宇等. 离轴多反射镜系统支撑结构的设计与装调[J]. 光学精密工程, 2015,23(8): 2280-2287

MEI Gui, ZHAI Yan, MIAO Jian-yu etc. Design and alignment of support structure for off-axis multi-mirror system[J]. Editorial Office of Optics and Precision Engineering, 2015,23(8): 2280-2287
梅贵, 翟岩, 苗健宇等. 离轴多反射镜系统支撑结构的设计与装调[J]. 光学精密工程, 2015,23(8): 2280-2287 DOI： 10.3788/OPE.20152308.2280.

MEI Gui, ZHAI Yan, MIAO Jian-yu etc. Design and alignment of support structure for off-axis multi-mirror system[J]. Editorial Office of Optics and Precision Engineering, 2015,23(8): 2280-2287 DOI： 10.3788/OPE.20152308.2280.

摘要

针对离轴多反射式空间相机设计了一种胶接桁架支撑结构。采用T700碳纤维复合材料制造桁架杆

钛合金材料制造杆接头

J133环氧树脂胶作为黏合剂

桁架杆两端的钛合金接头作为相机各组件的接口。给出了装调和胶接的辅助设备及相应的方法和步骤:即利用工装进行预装调

确定杆接头位置;然后通过抹胶完成正式装调

利用定位销钉实现杆接头复位;最后在室温下固化5~7天

拆除工装和销钉后桁架装调完毕。有限元分析和力学振动试验表明

固化完成的桁架一阶谐振频率优于90 Hz

所支撑镜头的一阶谐振频率优于70 Hz。对力学试验前后桁架的各反射镜接口平面度进行了测量

结果显示其最大相对偏差为5.3%

平面度均优于0.15 mm。得到的结果表明该桁架的刚度及尺寸稳定性均满足设计要求。

Abstract

A support structure with an adhesive truss was designed for a space camera with off-axis multi-mirror systems. The struts of this truss were manufactured with T700 made of carbon fiber composites

fittings were manufactured with titanium alloys

the adhesive was J133 epoxy resin and casting titanium fittings were bonded on both ends of the truss struts to provide interfaces for other subassemblies of the camera. The methods and steps for assist alignment equipment and gluing the subassemblies were described particularly. Firstly

preliminary assembly and alignment were done to ensure the precise locations of struts and fittings using the assistance equipment. Then

the formal alignment was performed with the help of locating pins

and the struts and fittings were restored in the correct initial positions and bonded with adhesives. Finally

the structure was solidified at room temperature for 5-7 days

and the assembly and alignment were finished after dismantling the assistance equipment and pins.The results of finite element analysis and vibration test indicate that the first-order natural frequencies of the truss and the lens supported by the truss are more than 90 Hz and 70Hz

respectively. Interfaces of mirror subassemblies were measured before and after vibration tests

and the results show that the flatness has been reached to 0.15 mm and the maximum relative error of interface flatness is 5.3%. The conclusion is that the stiffness and dimensional stability of the truss well meet the design requirements.

关键词

Keywords

references

范斌,王艳. 国外长焦距高分辨率遥感相机桁架结构研究[J]. 航天遥感与返回,2008,29(2):35-41. FAN B, WANG Y. Research on truss structure of foreign remote-sensing cameras with long focal length and high resolution [J]. Spacecraft Recovering and Remote Sensing, 2008, 29(2): 35-41.(in Chinese)

李威,刘宏伟. 空间光学遥感器中碳纤维复合材料精密支撑构件的结构稳定性[J]. 光学精密工程,2008,16(11):2173-2179. LI W, LIU H W. Structure stability of precision component made of carbon fiber composite in space optical remote sensor [J]. Opt. Precision Eng., 2008, 16(11): 2173-2179. (in Chinese)

孙敬伟,吕天宇,姚丽双,等. 发射望远镜的设计与装调[J]. 光学精密工程,2014,22(2):369-375. SUN J W, LV T Y, YAO L SH, et al.. Design and assembly of transmitter-telescope [J]. Opt. Precision Eng., 2014, 22(2): 369-375. (in Chinese)

SEBASTIAN S, CHRISTOPH D, WOLFGANG H, et al.. Ultra precisely manufactured mirror assemblies with well defined reference structures [J]. SPIE, 2010, 773908: 1-10.

徐伟,朴永杰. 从Pleiades剖析新一代高性能小卫星技术发展[J]. 中国光学,2013,6(1):9-19. XU W, PU Y J. Analysis of new generation high-performance small satellite technology based on Pleiades [J]. Chinese Optics, 2013, 6(1): 9-19. (in Chinese)

孔林,王栋,姚劲松,等. 轻型空间相机支撑桁架的精确控温[J]. 光学精密工程,2014,22(3):712-719. KONG L, WANG D, YAO J S, et al.. Precision temperature control for supporting trusses of lightweight space cameras [J]. Opt. Precision Eng., 2014, 22(3): 712-719. (in Chinese)

郭权峰.同轴三反空间相机结构稳定性研究[D]. 北京:中国科学院研究生院,2012. GUO Q F.Research on structure stability of three-mirror cassegrain space camera [D]. Beijing: Graduate University of the Chinese Academy of Sciences, 2012. (in Chinese)

ANTEBI J, DUSENBERY D O, LIEPINS A A. Conversion of the MMT into a 6.5-m telescope: the optics support structure and enclosure[J]. Proc. SPIE, 1998,513:3352.

张雷,姚劲松,贾学志,等. 同轴空间相机碳纤维复合材料桁架结构的研制[J]. 光学精密工程,2012, 20(9): 1967-1973. ZHANG L, YAO J S, JIA X ZH, et al.. Development of trusses made of carbon fiber composites for coaxial space remote sensors [J]. Opt. Precision Eng., 2012, 20(9): 1967-1973. (in Chinese)

贾学志,张雷,金光. 空间相机桁架支撑结构满应力优化设计与试验[J]. 空间科学学报,2013, 33(3): 346-352. JIA X ZH, ZHANG L, JIN G.. Optimum design based on full stress ruler and test for truss of space camera [J]. Chin. J. Space Sci., 2013, 33(3): 346-352. (in Chinese)

李志来. 长焦距空间相机主次镜间桁架支撑结构设计[J]. 激光与红外,2012, 42(1): 89-93. LI ZH L. Truss support structure design between primary mirror and secondary mirror in long focal length space camera [J]. Laser & Infrared, 2012, 42(1):89-93. (in Chinese)

PAUL R, YODER J. Opto-Mechanical Systems Design [M]. Third edition, Boca Raton: CRC Press, Taylor & Francis Group, 2006: 706-729.

刘磊.空间光学遥感器轻型支撑结构研究[D]. 北京:中国科学院研究生院,2006. LIU L. Research on light-weight frame of the space optical remote sensor[D]. Beijing: Graduate University of the Chinese Academy of Sciences, 2006. (in Chinese)

郭疆,邵明东,王国良,等. 空间遥感相机碳纤维机身结构设计[J]. 光学精密工程,2012,20(3):571-578. GUO J, SHAO M D, WANG G L, et al.. Design of optical-mechanical structure made of CFC in space remote sensing camera[J]. Opt. Precision Eng., 2012, 20(3): 571-578. (in Chinese)

辛宏伟,关英俊,柴方茂. 离轴空间遥感器主支撑结构设计[J]. 光学精密工程,2012, 20(6):1257-1264. XIN H W, GUAN Y J, CHAI F M. Design of main support of off-axis space remote sensor [J]. Opt. Precision Eng., 2012, 20(6):1257-1264. (in Chinese)

安源,贾学志,张雷,等. 基于碳纤维符合材料的空间相机高比刚度主承力板优化设计[J]. 光学精密工程,2013, 21(2):416-422. AN Y, JIA X ZH, ZHANG L, et al.. Optimizing design of CFRP based main backbone with high stiffness ratio for space camera [J]. Opt. Precision Eng., 2013, 21(2): 416-422. (in Chinese)

林再文,刘永琪,梁岩,等. 碳纤维增强复合材料在空间光学结构中的应用[J]. 光学精密工程,2007, 15(8): 1181-1185. LIN Z W, LIU Y Q, LIANG Y, et al.. Application of carbon fiber reinforced composite to space optical structure [J]. Opt. Precision Eng., 2007, 15(8):1181-1185. (in Chinese)

崔永鹏,何欣,张凯. 钛合金和碳纤维的粘接技术[J]. 光学技术,2012,38(1):125-128. CUI Y P, HE X, ZHANG K. Technique of cementation between the titanium alloys and carbon fibers [J]. Optical Technique, 2012, 38(1):125-128.(in Chinese)

刘良威,刘锦,李志慧,等. 复合材料桁架胶接装配技术[J]. 宇航材料工艺,2013(4):102-104. LIU L W, LIU J, LI ZH H, et al.. Technology of cementing and assembling composite truss[J]. Aerospace Materials & Technology,2013(4):102-104. (in Chinese)

张凯,何欣,赵海平. 空间遥感相机桁架机身接头结构的设计和分析[J]. 红外,2013, 34(10): 10-15. ZHANG K. HE X. ZHAO H P. Design and analysis of joints for truss structure of space camera [J]. Infrared, 2013, 34(10): 10-15. (in Chinese)

Views

823

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Design of truss adjusting mechanism for secondary mirror of large aperture telescope

Alignment of multi-beam laser emission system

Optimization of carbon fiber truss element for primary mirror chamber of large telescope

Design and optimization of carbon fiber framework for space camera

Optimization design of flexible and damping support structure of space camera

Related Author

CHEN Jianbo

YANG Fei

WANG Fuguo

ZHANG Benlei

LU Baowei

Sheng-bo MU

Yang LI

He-fei LIU

Related Institution

University of Chinese Academy of Sciences

Changchun Institute of Optics，Fine Mechanics and Physics，Chinese Academy of Sciences

Beijing Institute of Space Mechanics & Electricity

Key Laboratory of Astronomical Optics & Technology， Nanjing Institute of Astronomical Optics & Technology， Chinese Academy of Sciences

National Astronomical Observatories / Nanjing Institute of Astronomical Optics & Technology， Chinese Academy of Sciences

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰