Correction of angle measuring errors for large telescopes

WANG Xian-jun

doi:10.3788/OPE.20152309.2446

您当前的位置：

首页 >

文章列表页 >

Correction of angle measuring errors for large telescopes

更新时间：2020-08-12

- Correction of angle measuring errors for large telescopes
- Optics and Precision Engineering Vol. 23, Issue 9, Pages: 2446-2451(2015)
- 作者机构：
  
  中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20152309.2446
  CLC： TP212.12;TH743
- Received：29 December 2014，
  
  Revised：20 February 2015，
  
  Published：25 September 2015
- 稿件说明：
移动端阅览
王显军,. 大型望远镜测角系统误差的修正[J]. 光学精密工程, 2015,23(9): 2446-2451

WANG Xian-jun,. Correction of angle measuring errors for large telescopes[J]. Editorial Office of Optics and Precision Engineering, 2015,23(9): 2446-2451
王显军,. 大型望远镜测角系统误差的修正[J]. 光学精密工程, 2015,23(9): 2446-2451 DOI： 10.3788/OPE.20152309.2446.

WANG Xian-jun,. Correction of angle measuring errors for large telescopes[J]. Editorial Office of Optics and Precision Engineering, 2015,23(9): 2446-2451 DOI： 10.3788/OPE.20152309.2446.

摘要

由于大型望远镜转台轴系对测角精度要求较高

本文研究了测角数据系统的误差修正技术。分析了测角数据误差产生的原因

对测角元件误差、安装误差、被测轴系误差进行了讨论

指出轴系测角分系统的误差规律符合谐波方程

故提出采用谐波方程式来表达误差规律。针对工程应用

建立了基于傅里叶级数的简化谐波方程误差公式

用谐波方程算法和多项式拟合算法对系统误差进行修正。在一个望远镜垂直轴转台进行了试验验证

结果显示测角精度峰值由原来的3.81"提高到了1.06"。实验表明

基于傅里叶级数的修正算法

较好地符合误差分布规律;采用系统误差修正技术

可以对系统综合误差统一修正

能够有效提高系统测角精度。

Abstract

As the turntable shaft system of a large telescope needs a higher angle measuring precision

this paper explores an error correction method for the angle measuring system. The causes of data errors of angle measuring were analyzed

and the errors of angle measuring device

installation errors and the errors of measured shaft were discussed. It points out that the error rules of the shaft angle measuring subsystem are according with a resonant equation

so the resonant equation was used to explain the error rule. For engineering applications

a simplified resonant equation error formula was established through the research of the Fourier series

Then

the harmonic equation algorithm and the polynomial fitting algorithm were used to correct the system errors. A test was taken on the vertical axis turntable of a telescope and the results show that the peak of angle measurement precision is improved from 3.81"to 1.06". The experiments indicate that the modified algorithm based on Fourier series conforms the error distribution rule better. The error correction method corrects comprehensive errors of the system in a unified way and effectively improves the angle measurement precision of the system.

关键词

Keywords

references

王建立,陈涛,张景旭. 地基高分辨率光电成像望远镜总体需求及关键技术分析[J]. 光学精密工程,2008,16(5):1-16. WANG J L, CHEN T, ZHANG J X. General requirements and key technologies for the ground-based high resolution EO imaging telescope [J]. Opt. Precision Eng.,2008,16(5):1-16. (in Chinese)

艾晨光,褚明,孙汉旭,等. 基准圆光栅偏心检测及测角误差补偿[J]. 光学精密工程,2012,20(11):2479-2484. AI CH G,CHU M,SUN H X,et al.. Eccentric testing of benchmark circular grating and compensation of angular error [J]. Opt. Precision Eng.,2012,20(11):2479-2484.(in Chinese)

张红胜,杨进堂. 光学码盘的检验[J]. 计量技术,1999(10):25-27. ZHANG H SH,YANG J T. Testing of optical encoder[J]. Metrology Technology,1999(10):25-27. (in Chinese)

王显军. 光电轴角编码器细分信号误差及精度分析[J]. 光学精密工程,2012,20(2):379-386. WANG X J. Errors and precision analysis of subdivision signals for photoelectric angle encoders[J]. Opt. Precision Eng.,2012,20(2):379-386. (in Chinese)

吕孟军,郭琪,吕印晓. 莫尔条纹信号相位误差补偿[J]. 光学精密工程,2009,17(7):1694-1700. LV M J,GUO Q,LV Y X. Signal phase error compensation of Moire fringe[J]. Opt. Precision Eng., 2009,17(7):1694-1700. (in Chinese)

祝成军,龙科慧. 光电编码器信号幅值自动补偿方法的研究[J]. 测控技术,2009,28(9):6-12. ZHU CH J, LONG K H.Research on the method of signal amplitude automatic compensation for photoelectric encoder [J]. Measurement & Control Technology,2009,28(9):6-12. (in Chinese)

王显军,杨晓霞. 光电编码器的应用-分辨率和精度[J]. 光机电信息,2011,28(9):6-11. WANG X J,YANG X X. The application of optical encoder-differentiate and precision[J]. OME Information,2011,28(9):6-11. (in Chinese)

高福晖. 大型经纬仪轴系晃动的傅里叶谐波分析方法[J]. 光电工程,1998,25(5):1-10,15. GAO F H. Fourier harmonic analysis method for axial system wobbling of the large scale theodolite[J]. Opt.Electronic Engineering,1998,25(5):1-10,15. (in Chinese)

冯栋彦,高云国,张文豹. 采用标准轴承的光电经纬仪轴系误差修正[J]. 光学精密工程,2011,19(3):605-611. FENG D Y, GAO Y G,ZHANG W B. Elimnation of shafting error in photoelectrical theodolites with standard bearings[J]. Opt. Precision Eng.,2011,19(3):605-611. (in Chinese)

潘年,马文礼. 拼接式钢带光栅编码器测角误差分析与修正[J]. 中国光学,2013,6(5):788-794. PAN N,MA W L. Error analysis and correction of scale tape grating encoder[J]. Chinese Optics,2013,6(5):788-794. (in Chinese)

Views

448

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Multi-feature cross UAV image detection algorithm under cross-layer attentional interaction

Research on factors influencing the pointing accuracy of large telescopes and the correction model

Calibration and correction of geometric errors in laser tracker

Underwater image enhancement synthesizing multi-scale information and attention mechanisms

Correction of probe alignment error for ZC1 worm gear profile measurement

Related Author

ZHANG Zhihao

DU Lixia

HOU Yue

HAO Ziwei

YIN Jie

CHEN Baogang

XIA Haojie

ZHANG Jin

Related Institution

College of Electronic and Information Engineering， Lanzhou Jiaotong University

Hefei University of technology，College of Instrument Science and Optoelectronic Engineering

Changchun Institute of Optics，Fine Mechanics and Physics，Chinese Academy of Sciences

Institute of Microelectronics of the Chinese Academy of Sciences

University of Chinese Academy of Sciences

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰