FENG Qi-bin, YIN Hui-juan, CHENG Xin etc. Design of optical film with microstructure for viewing angle deflection[J]. Editorial Office of Optics and Precision Engineering, 2016,24(5): 1009-1014
FENG Qi-bin, YIN Hui-juan, CHENG Xin etc. Design of optical film with microstructure for viewing angle deflection[J]. Editorial Office of Optics and Precision Engineering, 2016,24(5): 1009-1014 DOI: 10.3788/OPE.20162405.1009.
Design of optical film with microstructure for viewing angle deflection
its max luminance direction usually has a certain angle with the direction of viewers. Therefore
this paper designs an optical film with a microstructure surface to allow the max luminance to be changed with the direction of viewers. Based on the luminous distribution of common backlight
the microstructure surface of the optical film was designed as a right triangle. In consideration of the total reflection of the right-angle side
narrower half-luminance angle range and its cut-off angle
the height and the angle of the microstructure were optimized to improve the half-luminance angle ranges. To eliminate cut-off angle and to increase half-luminance angle ranges further
the microstructure was optimized once again
and the outline with two peaks for the microstructure was proposed. The simulation results show that when the horizontal viewing angle doesn't change
the vertical viewing angle is at about 20°
the transmittance is 87.3% and the half-luminance angle ranges are (-12.5°
45°). On the basis of the design
a sample was produced and measured. The practical measurement results show that the angle of max luminance turns from 0° to 18.9°
the half-luminance viewing angle changes from (-24.1°
23.5°) to (-9.2°
45.3°)
and the transmittance is 82.0% as compared with the common backlight without the optical film. These results satisfy the requirements of special viewing angles.
关键词
Keywords
references
MUNISAMY A. Progress of LED backlights for LCDs[J]. Journal of the Society for Information Display, 2008,16(2):287-310.
FENG Q B, HE H J, ZHANG W W, et al.. Global dimming algorithm for side-lit LED backlight[J]. Journal of Optics and Precision Engineering, 2012, 20(7):1455-1462.
GOURLAY, JAMES. Energy efficient LED backlight technology[J]. SID Symposium Digest of Technical Papers,2013, 44(1):222-225.
FENG D, YAN Y B, YANG X P, et al.. Novel integrated light-guide plates for liquid crystal display backlight[J]. Pure and Applied Optics,2005,7(3):111-117.
SHER C W, YAO P H, CHEN C H, et al.. Compact pixelized LED backlight for LCD[J]. SID Symposium Digest of Technical Papers, 2013, 44(1):824-827.
YOUNG J J, MYONGJO C, YOUNGSIK O, et al.. Collimation sheet design for the one-side edge-lit backlight[J]. SID Symposium Digest of Technical Papers, 2011, 42(1):1427-1429.
KÄLIL K. An intensively lit collimating unit for the realization of a mosaic-structured large-scale RGB backlight[J]. Journal of the Society for Information Display, 2006, 14(8):687-694.
TSOU C, CHANG C, LAI T, et al.. Novel direct-view LED backlight unit with an aspheric microlens array and a rough-texture sheet[J]. J. Soc. Inf. Display, 2010, 18(5):336-345.
LEE J H, LEE H S, LEE B K, et al.. Design and fabrication of a micropatterned polydimethylsiloxane (PDMS) light-guide plate for sheet-less LCD backlight unit[J]. Journal of the Society for Information Display, 2008, 16(2):329-335.
庄孝磊, 周芳, 申溯, 等. 层叠微透镜阵列光扩散片特性研究[J]. 光学学报, 2010, 30(11):3306-3309. ZHANG X L, ZHOU F, SHEN S, et al.. Characteristics of diffusers with cascaded-microlens arrays[J]. Acta Optica Sinica, 2010, 30(11):3306-3309.(in Chinese)
TENG T C, KE J C.A novel optical film to provide a highly collimated planar light source[J].Optical Express, 2013,21(18):21444-21455.
秦宗. 大尺寸高性能LED背光模组关键技术研究[D]. 武汉:华中科技大学,2013. QING Z. Resserch on Key Techniques of Large-size LED Backlight Module with High Performance[D]. Wuhan:Graduate University of the Huazhong University of Science and Technology, 2013. (in Chinese)
FAN C W, PAN J W, TU S H. A novel backlight system with high on-axis luminance and small viewing angle[J]. SID Symposium Digest of Technical Papers, 2011,42(1):886-889.