Roughness evaluation of 3D surface profile

LIU Bo; QI Xing-hua; ZHANG Ming

doi:10.3788/OPE.20162413.0135

您当前的位置：

首页 >

文章列表页 >

Roughness evaluation of 3D surface profile

更新时间：2020-08-13

- Roughness evaluation of 3D surface profile
- Optics and Precision Engineering Vol. 24, Issue 10s, Pages: 135-140(2016)
- 作者机构：
  
  哈尔滨理工大学测控技术与通信工程学院,黑龙江哈尔滨,150080
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20162413.0135
  CLC： TH741
- Received：28 May 2016，
  
  Revised：12 June 2016，
  
  Published：14 November 2016
- 稿件说明：
移动端阅览
刘泊, 齐兴华, 张明. 表面三维轮廓的粗糙度评定[J]. 光学精密工程, 2016,24(10s): 135-140

LIU Bo, QI Xing-hua, ZHANG Ming. Roughness evaluation of 3D surface profile[J]. Editorial Office of Optics and Precision Engineering, 2016,24(10s): 135-140
刘泊, 齐兴华, 张明. 表面三维轮廓的粗糙度评定[J]. 光学精密工程, 2016,24(10s): 135-140 DOI： 10.3788/OPE.20162413.0135.

LIU Bo, QI Xing-hua, ZHANG Ming. Roughness evaluation of 3D surface profile[J]. Editorial Office of Optics and Precision Engineering, 2016,24(10s): 135-140 DOI： 10.3788/OPE.20162413.0135.

摘要

为了更直观地获取样块表面三维轮廓的粗糙度信息，以衡量所测试零件的表面质量，进而衡量其加工工艺的优劣以及能否满足设计要求，研究了一种表面三维形貌的评定方式。利用白光相移干涉系统测量标准样块的表面三维轮廓数据，建立高斯评定基准面并提取粗糙度数据，数据处理后对最为重要的幅度参数和综合参数加以计算，分析各个参数所反映的表面三维结构特征，并对标准样块的表面形貌进行了全面综合分析。实验结果显示，均方根偏差与粗糙度的比值为1.04，表面十点高度为0.059

m，偏斜度大于0，陡度小于3，均方根斜率为2.993

m，表面峰曲率算数平均值为0.181

m。该实验结果符合研磨样板表面轮廓的分布特征，并且与用轮廓仪的测量结果相符。

Abstract

To directly capture the roughness of the three-dimensional surface profile for surface quality evaluation of the tested parts

thus weighing its processing technology and whether relevant design requirements are satisfied

an evaluation method for the three-dimensional surface profile was put forward. Relevant data on three-dimensional surface profile of the standard sample piece was measured by using the white-light phase-shifting interference system. Then the Gaussian reference plane was set up and the roughness data was extracted. The most important parameters such as amplitude and integrated parameters were calculated after data processing

for analyzing structural feature of the three-dimensional surface reflected by each parameter. Finally the surface profile of the standard block was analyzed comprehensively. The results show that the ratio of the root-mean-square deviation to roughness is 1.04

and ten-point height of the surface is 0.059

m; the degree of skewness is greater than 0 and gradient less than 3; the root-mean-square(RMS) slope is 2.993

and average curvature of roughness peaks is 0.181

m. The experimental results conform to distribution characteristics of the surface profile of the grinding template

and in consistence with the measuring values by contourgraph.

关键词

Keywords

references

邹文栋,黄长辉,郑玱. 用扫描白光干涉术检测合金韧窝断口微观三维形貌[J]. 光学精密工程,2011,19(7):1612-1619. ZOU W D, HUANG C H, ZHENG Q. Detect the microscopic 3D morphology of alloy dimple fracture by scanning white light interferometry[J]. Opt. Precision Eng., 2011,19(7):1612-1619. (in Chinese)

高琦. 基于小波变换的金刚石砂轮表面形貌三维评定参数的研究[D]. 泉州:华侨大学,2014. GAO Q.Research on Three Dimensional Evaluation Parameters of Surface Topography of Diamond Grinding Wheel Based on Wavelet Transform[D]. Quanzhou:Huaqiao University, 2014. (in Chinese)

李满昌, 程庆柱, 李东. 表面粗糙度新旧国家标准差异的分析[J]. 林业机械与木工设备,2005,33(7):44-46. LI M CH, CHENG Q ZH, LI D.Analysis of the differences between the old and new national standard of surface roughness[J]. Forestry Machinery and Woodworking Equipment, 2005,33(7):44-46. (in Chinese)

商钰. 腐蚀环境对钢结构表面锈蚀特征影响的研究[D]. 西安:西安建筑科技大学,2011. SHANG Y.Study on the Corrosive Environment Influences on the Characteristics of the Steel-structure Surface[D]. Xi'an:Xi'an University of Architecture and Technology, 2011. (in Chinese)

李伯奎,李年莲,刘远伟,等. 表面粗糙度功能参数及其三维量值的实验研究[J]. 机械设计与制造, 2011(9):179-181. LI B K, LI N L, LIU Y W, et al.. Experimental study of surface roughness function parameters and its three dimension values[J]. Journal of Mechanical Design and Manufacturing, 2011(9):179-181. (in Chinese)

李成贵,董申. 三维表面微观形貌的表征趋势[J]. 中国机械工程,2000,11(5):488-492. LI CH G, DONG SH.The trends of three-dimensional surface micro topography characterization[J]. China Mechanical Engineering, 2000, 11(5):488-492. (in Chinese)

EGAN P, LAKESTANI F, WHELAN M P. Novel techniques for random depth access 3D white-light optical metrology[J].Interferometry XⅢ:Techniques and Analysis, 2006(8):212-213.

陈志杰. 微细电火花加工表面粗糙度评定研究[D]. 哈尔滨:哈尔滨工程大学,2011. CHEN ZH J.Research on Roughness Evaluation of the Micro Electrical Discharge Machining Surface[D]. Harbin:Harbin Engineering University, 2011. (in Chinese)

林滨, 黄新雁, 魏莹,等. 加工表面形貌测量理论、方法及评价[J]. 制造业自动化, 2006,28(8):14-18. LIN B, HUANG X Y, WEI Y, et al.. Measurement theory, method and evaluation of machined surface topography[J]. Journal of Manufacturing Automation, 2006, 28(8):14-18. (in Chinese)

杨练根,何浪,王选择,等. 波长轮换与相移扫描相结合的表面形貌测量系统[J]. 光学精密工程, 2015, 23(9):2466-2472. YANG L G, HE L, WANG X Z, et al.. Surface topography measurement system based on wavelength rotation and phase shift scanning[J]. Opt. Precision Eng, 2015, 23(9):2466-2472. (in Chinese)

杨本杰. 塑性变形界面表面形貌变化及摩擦特性研究[D]. 合肥:合肥工业大学, 2014. YANG B J.Study on Surface Topography Changes and Friction Characteristics of Plastic Deformation Interface [D]. Hefei:HeFei University of Technology, 2014. (in Chinese)

许景波,袁怡宝,刘泊. B样条滤波器建立表面轮廓中线的方法[J]. 光学精密工程, 2008,16(8):1411-1415. XU J B, YUAN Y B, LIU B.Method for establishing surface profile center line by B spline filter[J]. Opt. Precision Eng., 2008, 16(8):1411-1415. (in Chinese)

Views

648

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

White-light interferometry immune to vibration disturbance over wide frequency region

Influence of pH value on removal effect of fused silica during magnetorheological finishing

Image restoration based on adaptive group images sparse regularization

Magnetostrictive tactile sensor for texture detection

Suppression mechanics of returning wave speckle with multibeams illumination

Related Author

HUANG Xiaojin

MI Le

LIU Qian

Chao WANG

Xiao-yuan LI

Min-heng YE

Jia-bao LIU

Dong TIAN

Related Institution

Institute of Machinery Manufacturing Technology， China Academy of Engineering Physics

Institute of Machinery Manufacturing Technology, Chinese Academy of Engineering Physics

College of computer engineering, Jimei University

State Key Laboratory of Reliability and Intelligence of Electrical Equipment, Hebei University of Technology

Laboratory of Electromagnetic Field and Electrical Apparatus Reliability of Hebei Province, Hebei University of Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰