Fabrication of paper-based RFID tag antennas using jet printing and chemical deposition

Yuan XIAO; Jin-ling LIU; Shan WU; Song SHEN; Jin-rui ZHANG

doi:10.3788/OPE.20172503.0689

您当前的位置：

首页 >

文章列表页 >

Fabrication of paper-based RFID tag antennas using jet printing and chemical deposition

更新时间：2020-07-07

- Fabrication of paper-based RFID tag antennas using jet printing and chemical deposition
- Optics and Precision Engineering Vol. 25, Issue 3, Pages: 689-696(2017)
- 作者机构：
  
  西安工程大学机电工程学院, 陕西西安 710048
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20172503.0689
  CLC： TH16;TN820
- Received：19 October 2016，
  
  Accepted：12 November 2016，
  
  Published：25 March 2017
- 稿件说明：
移动端阅览
Yuan XIAO, Jin-ling LIU, Shan WU, et al. Fabrication of paper-based RFID tag antennas using jet printing and chemical deposition[J]. Optics and precision engineering, 2017, 25(3): 689-696.
DOI：

Yuan XIAO, Jin-ling LIU, Shan WU, et al. Fabrication of paper-based RFID tag antennas using jet printing and chemical deposition[J]. Optics and precision engineering, 2017, 25(3): 689-696. DOI： 10.3788/OPE.20172503.0689.

摘要

针对目前射频识别（RFID）标签天线制备成本高、工艺复杂等问题，提出微滴按需喷射3D打印与化学沉积技术相结合制备半波偶极子天线的方法。利用构建的气动式双喷头微滴喷射系统，采用试验研究的方法，对系统按需喷射条件下产生硝酸银与抗坏血酸微滴的一致性以及基板运行速度对成线均匀性的影响进行研究，并对成形导线的电阻率进行测试；在此基础上设计、仿真和制备了半波偶极子天线，对其性能参数进行了测试。结果表明：系统产生的微滴均匀性较好；基板速度小于或等于0.5 mm/s时，硝酸银成线边缘光滑度较好；成形导线的电导率为1.57×10

-5

Ω·m；打印成形的半波偶极子天线谐振频率、谐振点回波损耗

参数等与仿真结果具有较好的一致性。为RFID标签天线提供了一种低成本制备方法。

Abstract

Considering the problems of RFID (Radio Frequency Identification) tag antennas

including high manufacturing cost and complicated process

a method for fabrication of half wave dipole antennas combining 3D micro-droplet jet printing with chemical reaction deposition was put forward. Method: a constructed double nozzle pneumatic micro-droplet ejection device was used to carry out an experimental research on micro-droplet consistency of silver nitrate and ascorbic acid produced under the required ejection conditions the impacts of substrate speed on the line forming uniformity

and conducted a test in resistivity of the formed conductor; based on this

a half wave dipole antenna was designed

simulated and fabricated

and a test was conducted in its performance parameters. The results show that micro-droplet produced by the system is in good uniformity; when substrate speed is less than or equal to 0.5 mm/s

the line forming margin of silver nitrate is relatively smooth

and conductivity of the formed conductor is 1.57×10

-5

Ω·m; parameters of the printed half wave dipole antenna

such as the resonant frequency

resonance point return loss (

) etc

are in good consistency with the simulation results. Hence

the test provides a low-cost method for fabrication of RFID tag antennas.

关键词

Keywords

references

董健, 余夏苹, 任华斌, 等.一种UHF频段弯折偶极子RFID天线的设计[J].电子元件与材料, 2016, 35(2):47-51.

DONG J, YU X P, REN H B, et al..Design of a bending dipole RFID antenna at UHF band [J].Electronic Compoments and Materrials, 2016, 35(2):47-51. (in Chinese)

苏忠根.射频识别天线蚀刻技术工艺流程及其精益化管理研究[J].科技管理研究, 2014(1):218-223.

SU ZH G. Study of the RFID antennas etching process and quality controal management [J].Science and Technology Management Research, 2014(1):218-223. (in Chinese)

YANG L, RIDA A, VYAS R, et al..RFID tag and RF stucture on a paper substrate using inject printing technology [J]. IEEE Transactions on Microwave Theory and Techniques, 2007, 55(12):2894-2901.

MARK L A, JAAKKOLA K, NUMMILA K, et al..Applicability of metallic nanopartical Inks in RFID applications [J]. IEEE Transations on Components and Packaging technologies, 2009, 32(2):325-332.

杨利军, 李茜, 朱晓阳, 等.射频识别标签天线的按需微喷射制备[J].光学精密工程, 2016, 24(1):73-82.

YANG L J, LI X, ZHU X Y, et al..Fabrication of RFID tag antennas based on drop-on-demand technology [J].Opt. Precision Eng., 2016, 24(1):73-82. (in Chinese)

黄琦金, 沈文锋, 宋伟杰.反应喷墨打印技术及其在功能材料领域的研究进展[J].化学进展, 2015, 34(5):1332-1339.

HUANG Q J, SHEN W F, SONG W J.Development of reactive inkjet printing and its application in functional materials [J].Chemical Industry and Engineering Progress, 2015, 34(5):1332-1339. (in Chinese)

CHAURAYA A, WHITTOW W G, VARDAXOGLOU J C, et al..Inkjet printed dipole antennas on textiles for wearable communications [J].IET Microwaves, Antennas & Propagation, 2013, 7(9):1-22.

RUSHI V, VASILEIOS LAKAFOSIS A R, et al..Paper-based RFID-enabled wireless platforms for sensing applications [J].IEEE Transactions on Microwave Theory and Techniques, 2009, 57(5):1370-1382.

黄志爱. 基于喷墨打印工艺的RFID标签天线设计研究[D]. 大连: 大连理工大学, 2015.

HUANG ZH A. RFID Antenna Design and Research Based on Inkjet Printing Technology [D].Dalian:Da Lian University of Technology, 2015. (in Chinese)

周广洲, 蔡亚果, 张哲娟, 等.无颗粒型银导电墨水的制备及其性能研究[J].材料导报, 2016, 30(6):50-54.

ZHOU G ZH, CAI Y G, ZHANG ZH J, et al..Preparation of Non-particles Conductive SilverInk and electrical property [J].Materitals Review, 2016, 30(6):50-54.(in Chinese)

DONG H M. Drop-on-demand inkjet drop formation and deposition [D]. Georgia Institute of Technology, 2006.

王运赣, 张祥林.微滴喷射自由成形[M].武汉:华中科技大学出版社, 2009:8-91.

WANG Y G, ZHANG X L.Freeform Fabrication with Micro-droplet Jetting [M].Wuhan: Huazhong University of Science & Technology Press, 2009:8-91. (in Chinese)

薛光怀, 贺永, 傅建中, 等.压电式喷头的微滴喷射行为及其影响因素[J].光学精密工程, 2014, 22(8):2166-2172.

XUE G H, HE Y, FU J ZH, et al.. Droplet jetting of piezoelectric printhead and corresponding effcet factors [J].Opt. Precision Eng., 2014, 22(8):2166-2172.(in Chinese)

杨利军, 陆宝春, 朱晓阳, 等.数字化微喷射技术制备聚合物薄膜电阻[J].光学精密工程, 2015, 23(6):1598-1604.

YANG L J, LU B CH, ZH X Y, et al.. Fabrication of polymer thin film resistors by a drop-on-demand technology [J].Opt. Precision Eng., 2015, 23(6):1598-1604. (in Chinese)

肖渊, 黄亚超.气动式微滴喷射过程仿真与尺寸均匀性试验研究[J].中国机械工程, 2014, 25(21):2936-2941.

XIAO Y, HUANG Y CH.Simulation of pneumatic driven microdroplet jetting process and experimental study of microdroplet's uniformity [J].China Mechanical Engineering, 2014, 25(21):2936-2941. (in Chinese)

王春晖. 基于微流体数字化喷射技术的直写导线技术研究[D]. 南京: 南京理工大学, 2006.

WANG CH H. The Research of Direct Write Technology Based on Micro-fluids Digital Jet [D].Nanjing:Nan Jing University of Science & Technology, 2006. (in Chinese)

Views

866

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰