Influence of installation eccentricity on profile slope deviation of gear involute artifacts

Si-ying LING; Yi-lei CHEN; Ming LING; Dong-hui GAO; Hong-tao YANG

doi:10.3788/OPE.20192712.2581

您当前的位置：

首页 >

文章列表页 >

Influence of installation eccentricity on profile slope deviation of gear involute artifacts

更新时间：2020-07-09

- Influence of installation eccentricity on profile slope deviation of gear involute artifacts
- Optics and Precision Engineering Vol. 27, Issue 12, Pages: 2581-2589(2019)
- 作者机构：
  
  1.大连理工大学精密特种加工及微系统教育部重点实验室，辽宁大连 116023
  2.大连理工大学微纳米技术及系统辽宁省重点实验室，辽宁大连 116023
  3.安徽理工大学机械工程学院，安徽淮南 232001
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20192712.2581
  CLC： TG86
- Received：12 June 2019，
  
  Accepted：10 August 2019，
  
  Published：25 December 2019
- 稿件说明：
移动端阅览
Si-ying LING, Yi-lei CHEN, Ming LING, et al. Influence of installation eccentricity on profile slope deviation of gear involute artifacts[J]. Optics and precision engineering, 2019, 27(12): 2581-2589.
DOI：

Si-ying LING, Yi-lei CHEN, Ming LING, et al. Influence of installation eccentricity on profile slope deviation of gear involute artifacts[J]. Optics and precision engineering, 2019, 27(12): 2581-2589. DOI： 10.3788/OPE.20192712.2581.

摘要

为提高齿轮渐开线样板的制造精度，本文研究了齿轮渐开线样板安装偏心对其齿廓倾斜偏差的影响。基于双滚轮-导轨式渐开线展成原理，建立了齿轮渐开线样板安装偏心对其齿廓倾斜偏差影响的数学模型，并依据该模型分离出齿廓形状偏差和齿廓倾斜偏差；基于该数学模型，推导出补偿特定齿轮渐开线样板齿廓倾斜偏差所对应的安装偏心；最后，搭建了齿轮渐开线样板实验装置进行验证。实验结果表明：通过对安装偏心的补偿，可将齿轮渐开线样板齿廓倾斜偏差由-3.53 μm减小到-0.06 μm，达到了1级齿轮渐开线样板对齿廓倾斜偏差的要求。研究齿轮渐开线样板安装偏心对其齿廓倾斜偏差的影响规律可以用于补偿齿轮渐开线样板的齿廓倾斜偏差，并为开发高精度齿轮渐开线样板提供技术支持。

Abstract

In order to improve the manufacturing accuracy of gear involute artifacts

this study investigates the influence rule of installation eccentricity for gear involute artifacts on their profile slope deviation. Firstly

based on the involute generation principle of the double roller-guide

a mathematical model of the influence of installation eccentricity on the profile slope deviation of a gear involute artifact is developed

and the tooth profile form deviation are separated from the tooth profile slope deviations. Based on the mathematical model

the installation eccentricity corresponding to compensation of the profile slope deviation of gear involute artifact is deduced

and it is verified via test experiments. The experimental results demonstrate that the profile slope deviation of a gear involute artifact can be reduced from -3.53 μm to -0.06 μm

and the requirements for a class-1 gear involute artifact are satisfied. These conclusions on the influence rule of installation eccentricity on the profile slope deviation of gear involute artifacts can be used to compensate their tooth profile slope deviation and provide technical support for the development of high-grade gear involute artifacts.

关键词

Keywords

references

石照耀.齿轮行业将迎来第四次机遇[N].中国工业报, 2017-02-21(6).

SHI ZH Y. Gear industry will usher in the fourth opportunity[N]. China Industry News , 2017-02-21(6). (in Chinese)

GB/T 10095.1-2008圆柱齿轮精度制—第1部分: 轮齿同侧齿面的检验[S].北京: 中国标准出版社.

GB/T 10095.1-2008, Cylindrical gears-system of accuracy-Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth[S]. Beijing: China Standards Press. (in Chinese)

ISO_1328-1_2013(E). Cylindrical gears-ISO system of flank tolerance classification —Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth[S]. International Organization for Standardization, 2013.

孙桓, 陈作模, 等.机械原理[M].第七版.北京:高等教育出版社.

SUN H, CHEN Z M, et al. Mechanical Principles [M]. 7th Ed..Beijing: Higher Education Press.(in Chinese)

GBT 6467-2010.齿轮渐开线样板[S].北京: 中国标准出版社.

GB/T 6467-2010. The involute artifact of gear[S]. Beijing: China Standards Press. (in Chinese)

凌四营, 娄志峰, 王立鼎, 等.高等级渐开线样板精密磨削实验研究[J].大连理工大学学报, 2013(4):508-513.

LING S Y, LOU ZH F, WANG L D, et al. Experimental research on precision grinding for high-grade involute artifact[J]. Journal of Dalian University of Technology , 2013(4):508-513.(in Chinese)

覃爱梅, 陈燕云, 陈进来, 等.用三坐标机测量齿轮齿廓总偏差[J].装备制造技术, 2010, 2010(1):81-82.

QIN A M, CHEN Y Y, CHEN J L, et al. Measuring of gear tooth profile total deviation with coordinate measuring machine[J]. Equipment Manufacturing Technology , 2010, 2010(1):81-82.(in Chinese)

王立鼎, 娄志峰, 马勇, 等.双盘式渐开线测量仪精度分析[J].计量学报, 2009, 30(5):393-398.

WANG L D, LOU ZH F, MA Y, et al. Accuracy analysis of the double-disc instrument for measuring involute[J]. Acta Metrologica Sinica , 2009, 30(5):393-398.(in Chihese)

TAKEOKA F, KOMORI M, KUBO A, et al. High-precision measurement of an involute artefact by a rolling method and comparison between measuring instruments[J]. Measurement Science & Technology , 2009, 20(4):045105.

KOMORI M, TAKEOKA F, KUBO A, et al. Laser interferometric measuring method of involute artifact and stabilization of measurement[J]. IJAT , 2011, 5(2):144-149.

娄志峰.基准级渐开线测试理论与技术研究[D].大连: 大连理工大学, 2008. http://cdmd.cnki.com.cn/Article/CDMD-10141-2009040869.htm

LOU Z F. Research on Standard Involute Testing Theory and Technology [D]. Dalian: Dalian University of Technology, 2008.(in Chinese)

凌四营, 王立鼎, 李克洪, 等.基于1级精度基准标准齿轮的超精密磨齿工艺[J].光学精密工程, 2011, 19(7): 1596-1604.

LING S Y, WANG L D, LI K H, et al. Ultra-precision gear-grinding processing based on class 1 master gear[J] . Opt.Precision Eng. , 2011, 19(7): 1596-1604.(in Chinese)

王巧花, 叶平, 黄民.基于MATLAB的图形用户界面(GUI)设计[J].煤矿机械, 2005(3):60-62.

WANG Q H, YE P, HUANG M. Design of GUI based on MATLAB[J]. Coal Mine Machinery , 2005(3):60-62.(in Chinese)

李凯. UG NX运动仿真应用于机械结构设计[J].机械工程师, 2011(7):109-111.

LI K. UG NX motion simulation is applied to mechanical structure design[J]. Mechanical Engineer, 2011(7):109-111.(in Chinese)

莫江涛, 钟家宗, 龚佳兴.渐开线齿廓修形方法及应用[J].煤矿机械, 2018, 39(1):117-121.

MO J T, ZHONG J Z, GONG J X. Method of involute gear profile modification and its applications[J]. Coal Mine Machinery , 2018, 39(1):117-121.(in Chinese)

凌四营, 李军, 于佃清, 等.安装误差对直齿标准齿轮螺旋线偏差的影响规律[J].光学精密工程, 2017, 25(9): 2367-2376.

LING S Y, LI J, YU D Q, et al. Influence law of installation errors on helix deviation of spur gear artifact[J]. Opt.Precision Eng. , 2017, 25(9): 2367-2376.(in Chinese)

王立鼎, 娄志峰, 王晓东, 等.超精密渐开线齿形的测量方法[J].光学精密工程, 2006, 14(6):980-990.

WANG L D, LOU ZH F, WANG X D, et al. Measuring methods of ultraprecision involute tooth profile[J]. Opt.Precision Eng. , 2006, 14(6):980-990.(in Chinese)

佟晓冬, 王立鼎, 张玉玲, 等.高精度渐开线样板的测量[J].光学精密工程, 1993, 1(4):34-38.

TONG X D, WANG L D, ZHNAG Y L, et al. Measurement of high precision involute prototype[J]. Opt.Precision Eng. , 1993, 1(4):34-38.(in Chinese)

柳强.高精度鼓形渐开线凸轮加工理论与技术研究[D].大连: 大连理工大学, 2014. http://cdmd.cnki.com.cn/Article/CDMD-10141-1015572587.htm

LIU Q. Research on Processing Theory and Technology of High-precision Crown Involute Cam [D]. Dalian: Dalian University of Technology, 2014.(in Chinese)

吴淳杰, 董晨晨, 陈锋, 等.渐开线齿轮齿廓总偏差检测方法研究[J].计量与测试技术, 2017(8):56-58.

WU CH J, DONG CH CH, CHEN F, et al. Research on detection method for tooth profile of involute cylindrical gears[J]. Metrology & Measurement Technique , 2017(8):56-58.(in Chinese)

Views

142

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Measurement comparison for class-1 gear involute artifact in China

Research on error analysis and compensation method for deformation measurement of flexible wheel of harmonic drive

Related Author

LING Siying

LING Ming

SHI Zhaoyao

BO Lin

WANG Liding

Cong-bin YANG

Qing-xu GUO

Zhi-feng LIU

Related Institution

Key Laboratory for Micro/Nano Technology and System of Liaoning Province， Dalian University of Technology

Key Laboratory for Precision & Non-traditional Machining of Ministry of Education，Dalian University of Technology

Beijing Engineering Research Centre of Precision Measurement Technology and Instruments， Beijing Institute of Technology

State Key Laboratory of Mechanical Transmission， Chongqing University

Beijing University of Technology，Beijing Key Laboratory of Advanced Manufacturing Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰