Error analysis and compensation in position measurement of brake master cylinder compensation hole

Tao JIANG; Gui-lin ZHANG; Jun-peng GAO

doi:10.3788/OPE.20202805.1094

您当前的位置：

首页 >

文章列表页 >

Error analysis and compensation in position measurement of brake master cylinder compensation hole

Micro/Nano Technology and Fine Mechanics | 更新时间：2020-07-09

- Error analysis and compensation in position measurement of brake master cylinder compensation hole
- Optics and Precision Engineering Vol. 28, Issue 5, Pages: 1094-1100(2020)
- 作者机构：
  
  长春理工大学，吉林长春 130022
- 作者简介：
- 基金信息：
- DOI：10.3788/OPE.20202805.1094
  CLC： TH39; U463.51
- Received：22 October 2019，
  
  Revised：26 November 2019，
  
  Accepted：26 November 2019，
  
  Published：15 May 2020
- 稿件说明：
移动端阅览
Tao JIANG, Gui-lin ZHANG, Jun-peng GAO. Error analysis and compensation in position measurement of brake master cylinder compensation hole[J]. Optics and precision engineering, 2020, 28(5): 1094-1100.
DOI：

Tao JIANG, Gui-lin ZHANG, Jun-peng GAO. Error analysis and compensation in position measurement of brake master cylinder compensation hole[J]. Optics and precision engineering, 2020, 28(5): 1094-1100. DOI： 10.3788/OPE.20202805.1094.

摘要

针对当前制动主缸补偿孔检测效率低、精度低、成本高等技术现状，提出了一种集光、机、电于一体的高性能精密检测系统，分析了该系统所涉及的补偿孔几何中心位置检测误差并进行补偿。通过对误差来源的分析，揭示了制动主缸补偿孔位置检测过程的误差解算方法。基于该解算方法，利用增量式误差补偿方法构建了误差补偿模型，并进行补偿孔检测与误差补偿实验。实验结果表明，系统竖轴误差对补偿孔直径检测数据的影响较小，而对补偿孔位置检测数据的影响则由补偿孔与基准面的相对位置决定。补偿孔与基准面距离越远，误差越大。实验数据显示，在型号为ZDZG-20.64的被试件中，被测补偿孔位置精度分别提高0.05 mm和0.254 mm；在型号为ZDZG-22.2的被试件中，被测补偿孔位置精度分别提高0.044 mm和0.072 mm。该误差模型及补偿方法能够有效提高制动主缸补偿孔的检测精度。

Abstract

To address the problems regarding low efficiency

low accuracy

and high cost of brake master cylinder compensation hole measurement

a high-performance precision detection scheme based on optomechatronics was developed. After analyzing the error sources

an equation for error calculation with regard to brake master cylinder compensation hole measurement was derived. The analysis of the position measurement error led to the deduction of an incremental error compensation model

and an experiment was conducted for validation of the model. The experimental results show that the influence of vertical axis error on the measurement data for compensation hole diameter is minimal; however

it has significant influence on the position measurement data. The results show that the position accuracy of the compensation hole in ZDZG-20.64 standard part is improved by 0.05 mm and 0.254 mm. For ZDZG-22.2 standard part

the position accuracy is improved by 0.044 mm and 0.072 mm. The error model and compensation method can effectively improve the position detection accuracy of the brake master cylinder compensation hole.

关键词

Keywords

references

Z Q XU . Talking about the automobile braking system . IOP Conference Series: Materials Science and Engineering , 2017 . 274 012141 DOI: 10.1088/1757-899X/274/1/012141 http://doi.org/10.1088/1757-899X/274/1/012141 .

T ANTONIO , G ENRICO , V MAURO , 等 . Passenger car active braking system: pressure control design and experimental results (part Ii) . Proceedings of the Institution of Mechanical Engineers , 2018 . 232 ( 5 ): 786 - 798 . https://core.ac.uk/display/84252899 https://core.ac.uk/display/84252899 .

高俊鹏 , 姜涛 , 张桂林 , 等 . 汽车制动主缸补偿孔形位尺寸检测双远心光学系统研究 . 计量学报 , 2017 . ( 3 ): 262 - 266 . DOI: 10.3969/j.issn.1000-1158.2017.03.02 http://doi.org/10.3969/j.issn.1000-1158.2017.03.02 .

J P GAO , T JIANG , G L ZHANG , 等 . Research on double telecentric optical system for the form and position detection of automobile brake cylinder compensation hole . Acta Metrologica Sinica , 2017 . ( 3 ): 262 - 266 . DOI: 10.3969/j.issn.1000-1158.2017.03.02 http://doi.org/10.3969/j.issn.1000-1158.2017.03.02 .

董传宇.汽车液压制动主缸缸体补偿孔检测仪的研究[D].长春: 长春理工大学, 2015. http://cdmd.cnki.com.cn/Article/CDMD-10186-1016786405.htm

DONG CH Y. Research on Compensating Hole Detector of Automobile Hydraulic Break Cylinder [D]. Changchun: Changchun University of Science and Technology. 2015. (in Chinese)

彭辉.汽车制动主缸横孔去毛刺机研制[D].长春: 长春理工大学, 2017. http://cdmd.cnki.com.cn/Article/CDMD-10186-1017734979.htm

PENG H. The research on the Transverse Deburring Machine of Automobile Brake Master Cylinder [D]. Changchun: Changchun University of Science and Technology, 2017.(in Chinese)

O DURAN , K ALTHOEFER , L D SENEVIRATNE . Automated pipe defect detection and categorization using camera/laser-based profiler and artificial neural network . IEEE Transactions on Automation Science and Engineering , 2007 . 4 ( 1 ): 118 - 126 . DOI: 10.1109/TASE.2006.873225 http://doi.org/10.1109/TASE.2006.873225 .

鲁少辉.基于主动式全景视觉的管道内表面缺陷检测技术的研究[D].杭州: 浙江工业大学, 2017. http://cdmd.cnki.com.cn/Article/CDMD-10337-1017253260.htm

LU SH H. Research on defects detection technology of pipe internal surface based on active stereo omnidirectional vision [D]. Hangzhou: Zhejiang University of Technology, 2017.(in Chinese)

丁超 , 唐力伟 , 曹立军 , 等 . 深孔内表面结构光图像几何畸变校正 . 光学精密工程 , 2018 . 26 ( 10 ): 2555 - 2564 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201810024 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201810024 .

CH DING , L W TANG , L J CAO , 等 . Geometric distortion correction for structured-light image of deep-hole inner-surface . Opt. Precision Eng. , 2018 . 26 ( 10 ): 2555 - 2564 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201810024 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201810024 .

陈赟 , 高胜英 , 韩庆阳 , 等 . 多面体塔差及其安装偏心对光电编码器精度检测的影响 . 光学精密工程 , 2019 . 27 ( 8 ): 1704 - 1709 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201908004 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201908004 .

Y CHEN , SH Y GAO , Q Y HAN , 等 . Impact of polyhedron pyramidal error and installation eccentricity on precision detection of photoelectric encoder . Opt. Precision Eng. , 2019 . 27 ( 8 ): 1704 - 1709 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201908004 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201908004 .

王宏志 . 在线测量技术的误差分析-以汽车制动主缸补偿孔测量为例 . 内燃机与配件 , 2017 . ( 18 ): 26 - 28 . DOI: 10.3969/j.issn.1674-957X.2017.18.013 http://doi.org/10.3969/j.issn.1674-957X.2017.18.013 .

H ZH WANG . Error analysis of online measurement technology--taking the measurement of compensation shaft of automobile brake master cylinder as an example . Internal Combustion Engine & Parts , 2017 . ( 18 ): 26 - 28 . DOI: 10.3969/j.issn.1674-957X.2017.18.013 http://doi.org/10.3969/j.issn.1674-957X.2017.18.013 .

李林 , 王晓燕 , 钟俊 , 等 . 微尺度力敏器件力学特性及随机响应抑制研究 . 光学精密工程 , 2019 . 27 ( 7 ): 1561 - 1568 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201907018 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201907018 .

L LI , X Y WANG , J ZHONG , 等 . Study on mechanical properties and random response suppression of micro-scale mechanical-sensitive component . Opt. Precision Eng. , 2019 . 27 ( 7 ): 1561 - 1568 . http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201907018 http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201907018 .

M N GAJRE , R JEGADEESHWARAN , V SUGUMARAN , 等 . Vibration based fault diagnosis of automobile hydraulic brake system using fuzzy logic with best first tree rules . International Journal of Vehicle Structures and Systems , 2017 . 8 ( 4 ): 214 - 218 . http://maftree.org/eja/index.php/ijvss/article/view/558 http://maftree.org/eja/index.php/ijvss/article/view/558 .

Views

376

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Joint multiple optical theodolite tracking based outlier-tolerant least distance sum localization

Related Author

Jia-hui LIANG

Jian LI

Shao-lin HU

Related Institution

College of Automation and Information Engineering， Xi’an University of Technology

Norinco Group Test and Measuring Academy， Huayin

College of Automation， Guangdong University of Petrochemical Technology

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176855 Email：gxjmgc@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰