凸轮升程误差在三坐标测量机上的精确测量

黄富贵

doi:null

您当前的位置：

首页 >

文章列表页 >

凸轮升程误差在三坐标测量机上的精确测量

更新时间：2020-08-12

- 凸轮升程误差在三坐标测量机上的精确测量
- Accurate measurement of the cam’s lift error in the three-coordinates measuring machine
- 光学精密工程 2006年14卷第1期页码：111-115
- 作者机构：
  
  华侨大学机电及自动化学院,福建泉州,362021
- 作者简介：
- 基金信息：
- DOI：
  中图分类号： TH132.47
- 收稿日期：2005-10-22，
  
  修回日期：2005-12-18，
  
  网络出版日期：2006-02-20，
  
  纸质出版日期：2006-02-20
- 稿件说明：
移动端阅览
黄富贵. 凸轮升程误差在三坐标测量机上的精确测量[J]. 光学精密工程, 2006,14(1):111-115.

Huang Fu-gui. Accurate measurement of the cam’s lift error in the three-coordinates measuring machine[J]. Optics and precision engineering, 2006, 14(1): 111-115.
黄富贵. 凸轮升程误差在三坐标测量机上的精确测量[J]. 光学精密工程, 2006,14(1):111-115. DOI：

Huang Fu-gui. Accurate measurement of the cam’s lift error in the three-coordinates measuring machine[J]. Optics and precision engineering, 2006, 14(1): 111-115. DOI：

摘要

根据凸轮升程误差的设计要求与测量要求

提出了在三坐标测量机上用搜索点法实现的凸轮升程误差的测量方法

介绍了方法的原理、实现步骤

并对测量方法进行了误差分析。理论分析与测量实践表明

本文提出的凸轮升程误差测量方法的测量极限误差为±1.8 μm

比传统的凸轮升程误差测量方法如桃尖点法、敏感点法的测量极限误差小40%左右。

Abstract

A search point method was presented to measure cam's lift error on three-coordinates measuring machine according to the requirements of designing and measuring cam's lift error. The principle and steps of the new method were put forward

and the measurement error was analyzed. Academic analysis and practice in measuring show that the measurement error of this measuring method is ±1.8 μm

that is about sixty percent of the measurement error with the traditional measuring method such as the method of peach tip point

sensitivity point method.

关键词

Keywords

references

. BOOR D.On calculation with B-spline[J].Approx. Theory,1992,(6):50-62.

. LONCARIC S.A survey of shape analysis techniques[J].Pattern Recognition,1998.

. WONG Y S,ONG C J.Optimization approach for biarc curve-fitting of B-spline curves[J].CAD Computer Aided Design, 1996, 28(12):951-959.

. PATRIKALAKIS N M,KRIEZIS G A.Approximation of B-spline geometries with lower degree presentations.[J]. Journal of Offshore Mechanics and Arctic Engineering, 1990, 112(3):192-198.

. 刘兴富. 影响凸轮检测精度的问题与对策[J]. 广西机械,2001,(1):24-27. LIU X F.Problems in effecting cam measurement accuracy and its countermeasures [J].Guangxi Machine,2001,(1):24-27.(in Chinese)

. 黄富贵,张认成. 基于样条函数拟合的凸轮升程误差评定方法研究[J]. 计量学报,2004,25(4):306-309. HUANG F G,ZHANG R CH.The study on assessment method for the raising error of cam's curve based on spline function maching[J].Acta Metrologica Sinica, 2004,25(4):306-309.(in Chinese)

. 江少恩,刘忠礼,唐道源,等. 基于三次样条函数算法的逆阿贝尔变换[J]. 光学精密工程,2000,８(２):181-184. JIANG SH E,LIU ZH L,TANG D Y,et al.Inverted Abel transform based on cubic spline functions[J]. Optics and Precision Engineering,2000,8(2):181-184.(in Chinese)

. 陈锦昌,梁利车. 权因子对B样条曲线形状影响的研究[J]. 光学精密工程,2001,９(３):220-222. CHEN J CH,LIANG L D. Effect of weight factor on B-spline curves[J]. Optics and Precision Engineering. 2001,9(3):220-222.(in Chinese)

浏览量

324

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

并联坐标测量机研究进展

混频对全视场外差动态干涉仪测量精度的影响

寄生式时栅传感器动态测量误差的贝叶斯建模

基于坐标测量机的自由曲面检测采样策略

接触式大型非球面镜面形测量中测量点分布的确定