浏览全部资源
扫码关注微信
1.道路施工技术与装备教育部重点实验室(长安大学),陕西 西安 710064
2.柳州欧维姆机械股份有限公司,广西 柳州 545006
[ "夏晓华(1987-),男,山东临沂人,博士,副教授,2009 年于中国石油大学(华东)获得学士学位, 2015 年于西安交通大学获得博士学位,主要从事机器视觉与光机电一体化方面的研究。E-mail: xhxia@chd.edu.cn" ]
李玉强(1997-),男,陕西宝鸡人,硕士研究生,2020年于长安大学获得学士学位,主要从事机器视觉的研究。E-mail:2020225044@chd.edu.cn
收稿日期:2022-08-01,
修回日期:2022-09-16,
纸质出版日期:2023-06-10
移动端阅览
夏晓华,李玉强,邹易清等.圆柱曲面透视投影失真的图像校正[J].光学精密工程,2023,31(11):1691-1699.
XIA Xiaohua,LI Yuqiang,ZOU Yiqing,et al.Image correction for perspective projection distortion of cylindrical surface[J].Optics and Precision Engineering,2023,31(11):1691-1699.
夏晓华,李玉强,邹易清等.圆柱曲面透视投影失真的图像校正[J].光学精密工程,2023,31(11):1691-1699. DOI: 10.37188/OPE.20233111.1691.
XIA Xiaohua,LI Yuqiang,ZOU Yiqing,et al.Image correction for perspective projection distortion of cylindrical surface[J].Optics and Precision Engineering,2023,31(11):1691-1699. DOI: 10.37188/OPE.20233111.1691.
针对机器视觉系统中透视投影导致的钢管、桥梁拉索等圆柱表面缺陷测量不准的问题,提出了一种圆柱曲面透视投影失真的图像校正方法。该方法在提取圆柱成像区域、明确横向和轴向方向的基础上,基于圆柱曲面的透视投影特性,将产生的失真分解为轴向变形和横向变形,利用系统成像参数和圆柱半径建立校正图像与原图像的坐标对应关系,通过最邻近插值法进行像素映射实现透视投影失真校正。实验结果表明,该方法对不同直径圆柱的图像均有良好的校正效果,校正后的图像消除了圆柱曲面“近大远小”透视变形和倾斜投影变形;进行棋盘格模拟校正时,6个圆柱棋盘格边长的测量误差从校正前最高的14.9%降低至校正后的1.2%;进行划痕测量时,两种直径的原图像的最大误差分别为78.0%与61.8%,经本文方法校正后,两种直径的最大误差仅为5.9%与5.5%,校正效果显著。
To address the inaccurate measurement of cylindrical surface defects caused by perspective projection in machine vision systems, an image correction method to resolve cylindrical surface perspective projection distortion is proposed. In this method, the image area of the cylinder is first extracted. Then, the transverse and axial directions are determined. On the basis of the perspective projection characteristics of the cylindrical surface, the distortion is divided into axial and transverse deformation. The imaging parameters and cylindrical radius are utilized to establish the corresponding relationship between the coordinates of the original image and the those of the corrected image. The perspective projection distortion is corrected by pixel mapping and nearest neighbor interpolation. The experimental results demonstrate that the proposed method affords a good correction effect on images of different-diameter cylindrical surfaces. Both near-large and far-small perspective deformation and oblique projection deformation are eliminated in the corrected images. For the checkerboard simulation correction, the measurement error for the side length of the six cylindrical checkerboard squares decreases from a highest of 14.9% before correction to 1.2% after correction. In a scratch measurement, the maximum errors in the original image of two cylinders of different diameters are 78.0% and 61.8%. After correction using the proposed method, the maximum errors are only 5.9% and 5.5%, respectively. The remarkable correction effect verifies the effectiveness of the method.
BAUMUNG W . Application of machine learning and vision for real-time condition monitoring and acceleration of product development cycles [J]. Procedia Manufacturing , 2020 , 52 : 61 - 66 . doi: 10.1016/j.promfg.2020.11.012 http://dx.doi.org/10.1016/j.promfg.2020.11.012
刘坚 , 王媛媛 . 一种面向球姿态检测的图像透视畸变校正方法 [J]. 中国机械工程 , 2019 , 30 ( 18 ): 2242 - 2249, 2256 .
LIU J , WANG Y Y . A method of image perspective distortion correction in ball pose detections [J]. China Mechanical Engineering , 2019 , 30 ( 18 ): 2242 - 2249, 2256 . (in Chinese)
孙钊 , 许增朴 , 王永强 , 等 . 机器视觉测量中透视投影误差分析控制与补偿 [J]. 计算机工程与应用 , 2018 , 54 ( 2 ): 266 .
SUN ZH , XU Z P , WANG Y Q , et al . Control and compensation of perspective projection error analysis in machine vision measurement [J]. Computer Engineering and Applications , 2018 , 54 ( 2 ): 266 . (in Chinese)
刘宇飞 , 樊健生 , 聂建国 , 等 . 结构表面裂缝数字图像法识别研究综述与前景展望 [J]. 土木工程学报 , 2021 , 54 ( 6 ): 79 - 98 .
LIU Y F , FAN J SH , NIE J G , et al . Review and prospect of digital-image-based crack detection of structure surface [J]. China Civil Engineering Journal , 2021 , 54 ( 6 ): 79 - 98 . (in Chinese)
SHAO H , WANG Y X , DING D R , et al . Digital image aesthetic composition optimization based on perspective tilt correction [C]. 2020 Chinese Automation Congress (CAC). 68,2020 , Shanghai, China. IEEE , 2021 : 5267 - 5272 . doi: 10.1109/cac51589.2020.9327124 http://dx.doi.org/10.1109/cac51589.2020.9327124
周前飞 , 刘晶红 , 王宣 , 等 . 航空变焦距斜视成像几何畸变的自动校正 [J]. 光学 精密工程 , 2015 , 23 ( 10 ): 2927 - 2942 . doi: 10.3788/ope.20152310.2927 http://dx.doi.org/10.3788/ope.20152310.2927
ZHOU Q F , LIU J H , WANG X , et al . Automatic correction of geometric distortion in aerial zoom squint imaging [J]. Optics and Precision Engineering , 2015 , 23 ( 10 ): 2927 - 2942 . (in Chinese) . doi: 10.3788/ope.20152310.2927 http://dx.doi.org/10.3788/ope.20152310.2927
张亚锋 , 屠大维 , 蔡建文 , 等 . 任意位姿物体机器视觉测量视差变形补正 [J]. 仪器仪表学报 , 2017 , 38 ( 8 ): 2031 . doi: 10.3969/j.issn.0254-3087.2017.08.022 http://dx.doi.org/10.3969/j.issn.0254-3087.2017.08.022
ZHANG Y F , TU D W , CAI J W , et al . Parallax deformation correction of machine visual measurement toarbitrary position pose objects [J]. Chinese Journal of Scientific Instrument , 2017 , 38 ( 8 ): 2031 . (in Chinese) . doi: 10.3969/j.issn.0254-3087.2017.08.022 http://dx.doi.org/10.3969/j.issn.0254-3087.2017.08.022
LI D , TIAN J D . An accurate calibration method for a camera with telecentric lenses [J]. Optics and Lasers in Engineering , 2013 , 51 ( 5 ): 538 - 541 . doi: 10.1016/j.optlaseng.2012.12.008 http://dx.doi.org/10.1016/j.optlaseng.2012.12.008
ZHANG Z Y . Accuracy-enhanced constitutive parameter identification using virtual fields method and special stereo-digital image correlation [J]. Optics and Lasers in Engineering , 2018 , 103 : 55 - 64 . doi: 10.1016/j.optlaseng.2017.11.016 http://dx.doi.org/10.1016/j.optlaseng.2017.11.016
刘伟 , 周建行 , 杨延西 . 基于平行激光的便携式视觉裂缝测量系统 [J]. 仪器仪表学报 , 2020 , 41 ( 11 ): 235 - 243 .
LIU W , ZHOU J H , YANG Y X . Portable vision crack measurement system based on parallel laser [J]. Chinese Journal of Scientific Instrument , 2020 , 41 ( 11 ): 235 - 243 . (in Chinese)
钱炜燕 , 胡晓彤 . 基于柱面反投影算法的三维物体表面纹理重建 [J]. 天津科技大学学报 , 2009 , 24 ( 3 ): 58 - 62 . doi: 10.3969/j.issn.1672-6510.2009.03.015 http://dx.doi.org/10.3969/j.issn.1672-6510.2009.03.015
QIAN W Y , HU X T . Surface texture reconstruction for 3D object based on cylindrical back-projection algorithm [J]. Journal of Tianjing University of Science & Technology , 2009 , 24 ( 3 ): 58 - 62 . (in Chinese) . doi: 10.3969/j.issn.1672-6510.2009.03.015 http://dx.doi.org/10.3969/j.issn.1672-6510.2009.03.015
MENG G F , PAN C H , XIANG S M , et al . Metric rectification of curved document images [J]. IEEE Transactions on Pattern Analysis and Machine Intelligence , 2012 , 34 ( 4 ): 707 - 722 . doi: 10.1109/tpami.2011.151 http://dx.doi.org/10.1109/tpami.2011.151
王伟 , 何卫平 , 郭改放 , 等 . 基于标定的任意半径柱面上2维条形码畸变校正 [J]. 中国图象图形学报 , 2014 , 19 ( 1 ): 69 - 75 . doi: 10.11834/jig.20140109 http://dx.doi.org/10.11834/jig.20140109
WANG W , HE W P , GUO G F , et al . Restoration of distorted 2D barcode marked on arbitrary radius cylinder based on calibrated camera [J]. Journal of Image and Graphics , 2014 , 19 ( 1 ): 69 - 75 . (in Chinese) . doi: 10.11834/jig.20140109 http://dx.doi.org/10.11834/jig.20140109
孔明 , 孟繁明 , 王道档 , 等 . 圆柱工件表面缺陷视觉检测补偿方法研究 [J]. 中国计量大学学报 , 2018 , 29 ( 3 ): 244 - 250 . doi: 10.3969/j.issn.2096-2835.2018.03.003 http://dx.doi.org/10.3969/j.issn.2096-2835.2018.03.003
KONG M , MENG F M , WANG D D , et al . Research on a compensation method for the visual inspection of cylindrical workpiece defects [J]. Journal of China Jiliang University , 2018 , 29 ( 3 ): 244 - 250 . (in Chinese) . doi: 10.3969/j.issn.2096-2835.2018.03.003 http://dx.doi.org/10.3969/j.issn.2096-2835.2018.03.003
XU J M , CHEN C G , XIE H W , et al . Cylindrical product label image stitching method [C]. 2017 2nd IEEE International Conference on Computational Intelligence and Applications (ICCIA). 811,2017 , Beijing, China. IEEE , 2017 : 331 - 335 . doi: 10.1109/ciapp.2017.8167233 http://dx.doi.org/10.1109/ciapp.2017.8167233
朱飞鹏 , 龚琰 , 白鹏翔 , 等 . 基于数字图像相关的光学引伸计应变测量精度研究 [J]. 光学 精密工程 , 2018 , 26 ( 5 ): 1061 - 1069 . doi: 10.3788/ope.20182605.1061 http://dx.doi.org/10.3788/ope.20182605.1061
ZHU F P , GONG Y , BAI P X , et al . Study on strain measurement accuracy of optical extensometers based on digital image correlation [J]. Optics and Precision Engineering , 2018 , 26 ( 5 ): 1061 - 1069 . (in Chinese) . doi: 10.3788/ope.20182605.1061 http://dx.doi.org/10.3788/ope.20182605.1061
赵春华 , 贾玥泽 , 谭金铃 , 等 . 基于机器视觉的轴承外圈表面图像拼接方法 [J]. 科学技术与工程 , 2022 , 22 ( 14 ): 5729 - 5736 . doi: 10.3969/j.issn.1671-1815.2022.14.030 http://dx.doi.org/10.3969/j.issn.1671-1815.2022.14.030
ZHAO CH H , JIA Y Z , TAN J L , et al . Image mosaic method of bearing outer ring surface based on machine vision [J]. Science Technology and Engineering , 2022 , 22 ( 14 ): 5729 - 5736 . (in Chinese) . doi: 10.3969/j.issn.1671-1815.2022.14.030 http://dx.doi.org/10.3969/j.issn.1671-1815.2022.14.030
0
浏览量
306
下载量
1
CSCD
关联资源
相关文章
相关作者
相关机构