1.西安交通大学 机械工程学院 机械制造系统工程国家重点实验室,陕西 西安 710049
2.新拓三维技术(深圳)有限公司 创新实验室, 广东 深圳 518060
[ "尚国威(1999-),男,重庆人,硕士研究生,2021年于中南大学获得学士学位,主要从事机器视觉和三维光学测量方面的研究。E-mail: 3121101186@mail.xjtu.edu.cn" ]
[ "梁 晋(1968-),男,河南郑州人,博士,教授,博士生导师,1990年、1993年、2001年于西安交通大学分别获得学士、硕士和博士学位,主要从事机电控制、机器视觉等方面的研究。E-mail: liangjin@mail.xjtu.edu.cn" ]
扫 描 看 全 文
尚国威,梁晋,李磊刚等.空间最优投影平面的斜口圆截面管路端头位姿测量[J].光学精密工程,2024,32(01):95-110.
SHANG Guowei,LIANG Jin,LI Leigang,et al.Accurate measurement of end position of inclined pipe with optimal projection plane of space[J].Optics and Precision Engineering,2024,32(01):95-110.
尚国威,梁晋,李磊刚等.空间最优投影平面的斜口圆截面管路端头位姿测量[J].光学精密工程,2024,32(01):95-110. DOI: 10.37188/OPE.20243201.0095.
SHANG Guowei,LIANG Jin,LI Leigang,et al.Accurate measurement of end position of inclined pipe with optimal projection plane of space[J].Optics and Precision Engineering,2024,32(01):95-110. DOI: 10.37188/OPE.20243201.0095.
船舶、飞机等发动机为减小体积,采用斜口管路焊接代替弯头连接,管路系统中端头位姿是焊接对齐的前提。针对斜口管路端头位姿的高效高精度测量难题,提出了一种通过重建管路轴线以及管路端面进行端头位姿精确测量的方法。通过获取种子圆柱并设计非线性寻优算法提高圆柱拟合精度,通过高精度种子圆柱扩散重建得到管路轴线。通过双曲率阈值搜索方法对管路边缘进行搜索,得到管路端面边缘点整像素坐标。通过对端面提取得到的整像素坐标进行椭圆拟合结合射线求交方法求解端面边缘亚像素坐标,从而避免插值方法计算亚像素坐标受环境光源影响大的问题。最后,使用逐点最小二乘法重建空间投影平面并在平面上得到残差最小空间椭圆,空间椭圆中心即为管路端点,该投影平面即为端面所在平面,实现了对端头位姿的精确测量。实验结果表明,该方法的测量精度达到0.05 mm,角度测量误差小于0.1°,基本满足斜口管路端头的位姿测量精度要求,对管路的装配具有良好的指导意义。
To reduce the volume of ships, aircraft, and other engines, oblique pipe welding is used instead of elbow connection, and the end position in the pipeline system plays an important role in the welding alignment. First, the pipe axis was obtained by determining the seed cylinder and designing a nonlinear optimization algorithm. Then, the pipeline axis was obtained through diffusion reconstruction of the high-precision seed cylinder. Following this, the pipe edge was searched using the double curvature threshold search method, and the whole pixel coordinates of the end-face edge point of the pipe were obtained. Next, the subpixel coordinates of the end-face edge were obtained via elliptic fitting of the whole pixel coordinates extracted from the end face combined with the ray intersection method, avoiding the effect of the ambient light source on the subpixel coordinates calculated using the interpolation method. Finally, the spatial projection plane was reconstructed using the point-by-point least squares method and the minimal residual spatial ellipse was realized on the plane. The center of the elliptical circle of the space was the end of the pipe, and the projection plane was the plane where the end face was located, enabling accurate measurement of the head position. The experimental results show that the measurement accuracy of this method reaches 0.05 mm, and the angle measurement error is less than 0.1°, basically meeting the accuracy requirements of the head position measurement of an inclined pipeline, and presenting good guiding significance for the assembly of such pipelines.
空间投影平面管路端头位姿测量端面重建
spatial projection planepipelineendpoint pose measurementend face reconstruction
ZHOU L, WANG P, ZHANG CH J, et al. Multi-mode fusion BP neural network model with vibration and acoustic emission signals for process pipeline crack location[J]. Ocean Engineering, 2022, 264: 112384. doi: 10.1016/j.oceaneng.2022.112384http://dx.doi.org/10.1016/j.oceaneng.2022.112384
KIM W S, LEE D H, KIM Y J, et al. Stereo-vision-based crop height estimation for agricultural robots[J]. Computers and Electronics in Agriculture, 2021, 181: 105937. doi: 10.1016/j.compag.2020.105937http://dx.doi.org/10.1016/j.compag.2020.105937
赵玉芹, 张丽艳. 基于摄影测量的管路参数确定[J]. 机械制造与自动化, 2008, 37(6):114-117. doi: 10.3969/j.issn.1671-5276.2008.06.039http://dx.doi.org/10.3969/j.issn.1671-5276.2008.06.039
ZHAO Y Q, ZHANG L Y. Pipe parameter estimation in photogrammetry[J]. Machine Building & Automation, 2008, 37(6):114-117. (in Chinese). doi: 10.3969/j.issn.1671-5276.2008.06.039http://dx.doi.org/10.3969/j.issn.1671-5276.2008.06.039
李铁. 基于图像测量的汽车管件尺寸检测系统[D]. 长春: 吉林大学, 2005.
LI T. Size Detection System of Automobile Pipe Fittings Based on Image Measurement[D]. Changchun: Jilin University, 2005. (in Chinese)
BÖSEMANN W. The optical tube measurement system OLM photogrammetric methods used for industrial automation and process control[J]. International Archives of Photogrammetry and Remote Sensing, 1996, 31: 55-58.
VELDHUIS H, VOSSELMAN G. The 3D reconstruction of straight and curved pipes using digital line photogrammetry[J]. ISPRS Journal of Photogrammetry and Remote Sensing, 1998, 53(1): 6-16. doi: 10.1016/s0924-2716(97)00031-2http://dx.doi.org/10.1016/s0924-2716(97)00031-2
TANGELDER J W H, ERMES P, VOSSELMAN G, et al. CAD-based photogrammetry for reverse engineering of industrial installations[J]. Computer-Aided Civil and Infrastructure Engineering, 2003, 18(4): 264-274. doi: 10.1111/1467-8667.00316http://dx.doi.org/10.1111/1467-8667.00316
张天. 基于多目视觉的管路数字化测量方法研究[D]. 北京: 北京理工大学, 2014.
ZHANG T. Research on Digital Measurement Method of Pipeline Based on Multi-Vision[D]. Beijing: Beijing Institute of Technology, 2014. (in Chinese)
娄群, 吕钧澔, 文立华, 等. 基于亚像素边缘检测的高精度相机标定方法[J]. 光学学报, 2022, 42(20): 2012002. doi: 10.3788/aos202242.2012002http://dx.doi.org/10.3788/aos202242.2012002
LOU Q, LÜ J H, WEN L H, et al. High-precision camera calibration method based on sub-pixel edge detection[J]. Acta Optica Sinica, 2022, 42(20): 2012002.(in Chinese). doi: 10.3788/aos202242.2012002http://dx.doi.org/10.3788/aos202242.2012002
TAO L M,XIA R B,ZHAO J B. A high-accuracy circular hole measurement method based on multi-camera system[J]. Measurement, 2023, 207: 112361. doi: 10.1016/j.measurement.2022.112361http://dx.doi.org/10.1016/j.measurement.2022.112361
贾棋, 梁景朝, 王祎, 等. 基于区域检测和弧筛选的椭圆检测方法[J]. 计算机辅助设计与图形学学报, 2022, 34(11):1784-1794. doi: 10.3724/sp.j.1089.2022.19197http://dx.doi.org/10.3724/sp.j.1089.2022.19197
JIA Q, LIANG J CH, WANG Y, et al. Ellipse detection combining region detection and arc filtering[J]. Journal of Computer-Aided Design & Computer Graphics, 2022, 34(11):1784-1794.(in Chinese). doi: 10.3724/sp.j.1089.2022.19197http://dx.doi.org/10.3724/sp.j.1089.2022.19197
HOU X Y, LI M Z, LV Q, et al. Three-dimensional Measurement Method for Tube's Endpoints Based on Multi-view Stereovision[M]. Lecture Notes in Electrical Engineering. Singapore: Springer Nature Singapore, 2022: 283-290. doi: 10.1007/978-981-19-0386-1_35http://dx.doi.org/10.1007/978-981-19-0386-1_35
LIU S L, JIN P, LIU J H, et al. Accurate measurement method for tube’s endpoints based on machine vision[J]. Chinese Journal of Mechanical Engineering, 2017, 30(1): 152-163. doi: 10.3901/cjme.2016.0516.066http://dx.doi.org/10.3901/cjme.2016.0516.066
金鹏, 刘检华, 刘少丽, 等. 基于二维靶标的管路端点位置测量方法[J]. 计算机集成制造系统, 2014, 20(11): 2758-2766. doi: 10.13196/j.cims201411014http://dx.doi.org/10.13196/j.cims201411014
JIN P, LIU J H, LIU SH L, et al. Measuring method of pipeline endpoints based on two-dimensional point-target[J]. Computer Integrated Manufacturing Systems, 2014, 20(11): 2758-2766.(in Chinese). doi: 10.13196/j.cims201411014http://dx.doi.org/10.13196/j.cims201411014
张继耀. 采用边缘轮廓约束的航天发动机弯管几何参数多目视觉测量技术研究[D].西安:西安交通大学,2022. doi: 10.33737/gpps21-tc-240http://dx.doi.org/10.33737/gpps21-tc-240
ZHANG J Y. Study on Multi-Target Visual Measurement Technology for The Geometric Parameters of Space Engine Bend Pipes Constrained By Edge Contours [D]. Xi'an: Xi'an Jiaotong University, 2022.(in Chinese). doi: 10.33737/gpps21-tc-240http://dx.doi.org/10.33737/gpps21-tc-240
苗泽华. 工业弯管点云数据的YBC参数提取与检测方法研究[D].西安:西安交通大学,2021.
MIAO Z H. Research on YBC Parameter Extraction and Detection Method of Industrial Bent Pipe point Cloud Data [D]. Xi'an: Xi'an Jiaotong University, 2021.(in Chinese)
龚聪, 徐杜. 光源强度变化对图像检测精度的影响及其解决方法[J].科学技术与工程, 2014, 14(13): 236-239. doi: 10.3969/j.issn.1671-1815.2014.13.047http://dx.doi.org/10.3969/j.issn.1671-1815.2014.13.047
GONG C, XU D. Influence of light source intensity change on image detection accuracy and its solution[J]. Science Technology and Engineering, 2014, 14(13): 236-239.(in Chinese). doi: 10.3969/j.issn.1671-1815.2014.13.047http://dx.doi.org/10.3969/j.issn.1671-1815.2014.13.047
任同群, 江海川, 张建昆, 等. 微小磁性零件装配设备自动标定及误差补偿[J]. 光学 精密工程, 2023, 31(2): 214-225. doi: 10.37188/ope.20233102.0214http://dx.doi.org/10.37188/ope.20233102.0214
REN T Q, JIANG H CH, ZHANG J K, et al. Automatic calibration and error compensation for micro magnetic parts assembly equipment[J]. Opt. Precision Eng., 2023, 31(2): 214-225.(in Chinese). doi: 10.37188/ope.20233102.0214http://dx.doi.org/10.37188/ope.20233102.0214
石吉豪, 钟羽中, 郑秀娟, 等. 基于光线散射衰减模型的低照度图像增强[J]. 光学 精密工程, 2023, 31(8): 1244-1255. doi: 10.37188/ope.20233108.1244http://dx.doi.org/10.37188/ope.20233108.1244
SHI J H, ZHONG Y ZH, ZHENG X J, et al. Low-light image enhancement algorithm based on light scattering attenuation model[J]. Opt. Precision Eng., 2023, 31(8): 1244-1255.(in Chinese). doi: 10.37188/ope.20233108.1244http://dx.doi.org/10.37188/ope.20233108.1244
XIA Z Y, ZHAO J B, XIA R B. An improved method for correcting the eccentricity error of circular projection in the binocular visual system[C]. 2021 3rd International Symposium on Robotics & Intelligent Manufacturing Technology (ISRIMT). September 24-26, 2021. Changzhou, China. IEEE, 2021: 194-197.
0
浏览量
5
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构