积屑瘤状态对微细切削表面轮廓特征的影响

刘志兵; 王西彬

doi:10.3788/OPE.20111901.0090

您当前的位置：

首页 >

文章列表页 >

积屑瘤状态对微细切削表面轮廓特征的影响

微纳技术与精密机械 | 更新时间：2020-08-12

- 积屑瘤状态对微细切削表面轮廓特征的影响
- Influence of built-up edge phases on characteristics of surface profile of micro cutting
- 光学精密工程 2011年19卷第1期页码：90-96
- 作者机构：
  
  北京理工大学先进加工技术国防重点学科实验室,北京 100081
- 作者简介：
- 基金信息：
  
  国家自然科学基金资助项目(No.50935001,No.50875026)();高档数控机床与基础制造装备"();科技重大专项课题(No.2009ZX04014
- DOI：10.3788/OPE.20111901.0090
  中图分类号： TG501
- 收稿日期：2010-04-23，
  
  修回日期：2010-07-18，
  
  网络出版日期：2011-01-22，
  
  纸质出版日期：2011-01-22
- 稿件说明：
移动端阅览
刘志兵, 王西彬. 积屑瘤状态对微细切削表面轮廓特征的影响[J]. 光学精密工程, 2010,19(1): 90-96

LIU Zhi-bing, WANG Xi-bin. Influence of built-up edge phases on characteristics of surface profile of micro cutting[J]. Editorial Office of Optics and Precision Engineering, 2010,19(1): 90-96
刘志兵, 王西彬. 积屑瘤状态对微细切削表面轮廓特征的影响[J]. 光学精密工程, 2010,19(1): 90-96 DOI： 10.3788/OPE.20111901.0090.

LIU Zhi-bing, WANG Xi-bin. Influence of built-up edge phases on characteristics of surface profile of micro cutting[J]. Editorial Office of Optics and Precision Engineering, 2010,19(1): 90-96 DOI： 10.3788/OPE.20111901.0090.

摘要

研究了微细切削条件下

刀具前刀面上的积屑瘤状态对切削表面轮廓特征的影响

为合理选择和控制微细切削刀具的切削条件

以及评价微细切削的表面形貌特征提供实验依据。利用表面粗糙度仪分别提取了无积屑瘤、积屑瘤生长、稳定和脱落等4种积屑瘤状态下的切削表面轮廓

选取幅值密度函数(ADF)、自相关函数(ACF)和功率谱密度函数(PSD)等数理统计函数

以及时间序列模型参数和自回归(AR)谱分析了聚晶金刚石(PCD)刀具表面积屑瘤状态对微细切削表面轮廓特征的影响规律。结果表明

无积屑瘤和积屑瘤稳定阶段

AR谱的谱峰分别出现在91.7 c/mm和93.7 c/mm处

与进给量的倒数比较接近;积屑瘤生长和脱落状态阶段

谱峰出现的空间频率明显偏低

与进给量之间的对应关系不再显著。积屑瘤与切屑之间的不规则接触将破坏微细切削表面轮廓空间结构的一致性;积屑瘤生长和脱落阶段获得的表面轮廓的AR谱中存在明显的空间低频谱峰。

Abstract

The influences of Built-up Edge(BUE) phases of a rake face on the characteristics of surface profile of micro cutting were researched

which provided the proof for the optimal selection of cutting parameters and the evaluation for the characteristics of surface profile of micro cutting. The surface profile data in micro cutting were measured with a profilometer in different BUE phases

BUE free

BUE formation

BUE stable and BUE drop. The influences of the BUEs on the characteristics of machined surface profiles were analyzed with mathematical statistical functions such as Amplitude Density Function(ADF)

Auto-correlation Function(ACF) and Power Spectral Density Function(PSD)

as well as the time series model parameters and Auto Regression(AR) spectra. Obtained results indicate that in BUE free and BUE stable phases

the AR spectral peaks of micro cutting surface locate at 91.7 c/mm and 93.7 c/mm

respectively

which are very close to the reciprocal of a feed rate; while in BUE formation and BUE drop phases

the spatial frequency is significantly low compared with the reciprocal of feed rate. It is concluded that the consistency of the surface profile is deteriorated by the irregular contact between BUE and chip

and the low spatial frequency component becomes more dominant in the AR spectra of machined surface profile during BUE formation and BUE drop phases.

关键词

Keywords

references

韩雪松. 纳米切削工艺中刀具原子尺度磨损机理的分子动力学分析[J]. 机械工程学报,2007,43(9):107-112. HAN X S.Investigation atomic level micromechanism about tool wear in the case of nanometric cutting using molecular dynamics method[J].Chinese Journal of Mechanical Engineering,2007,43(9):107-112.(in Chinese)[2] 王大镇,韩荣第,刘华明,等. 铝基复合材料超精密加工中的刀－屑摩擦磨损性能及模型研究[J]. 摩擦学学报,2005,25(6):569-573. WANG D ZH,HAN R D,LIU H M,et al..Wear model and characteristics between cutting tool and chips in ultraprecisionmachining of SiC reinforced aluminum composites[J].Tribology,2005,25(6):569-573.(in Chinese)[3] CARRILERO M S,BIENVENIDO R,SNCHEZ J M.A SEM and EDS insight into the BUL and BUE differences in the turning processes of AA2024 AlCu alloy[J].International Journal of Machine Tools and Manufacture,2002,42(2):215-220.[4] KIM J D,MARINOV V R,KIM D S.Built-up edge analysis of orthogonal cutting by the visco-plastic finite-element method[J].Journal of Materials Processing Technology,1997,71(3):367-372.[5] MANNA A,BHATTACHARAYYA B.A study on machinability of Al/SiC-MMC[J].Journal of Materials Processing Technology,2003,140:711-716.[6] MENG Q,ARSECULARATNE J A,MATHEW P.Calculation of optimum cutting conditions for turning operations using a machining theory[J].International Journal of Machine Tools & Manufacture,2000,40:1709-1733.[7] OZCATABLBAS Y.Chip and built-up edge formation in the machining of in situ Al4C3-Al composite[J].Materials & Design,2003,24(3):215-221.[8] AKASAWA T,FUKUDA I,NAKAMURA K,et al..Effect of microstructure and hardness on the machinability of medium-carbon chrome-molybdenum steel[J].Journal of Materials Processing Technology,2004,153-154:48-53.[9] KIM J D,KANG Y H.High-speed machining of aluminium using diamond endmills[J].International Journal of Machine Tools & Manufacture,1997,37:1155-1165.[10] SANCHEZ J M,RUBIO E,LVAREZ M,et al..Microstructural characterisation of material adhered over cutting tool in the dry machining of aerospace aluminium alloys [J].Journal of Materials Processing Technology,2005,164-165:911-918.[11] ARSECULARATNE J A,FOWLE R F,MATHEW P.Nose radius oblique tool: cutting force and built-up edge prediction[J].Journal of Materials Processing Technology, 2005,164-165:911-918.[12] FANG N,DEWHURST P.Slip-line modeling of built-up edge formation in machining[J].International Journal of Mechanical Sciences,2005,47(7):1079-1098.

浏览量

457

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

反应连接230 mm口径RB-SiC反射镜