平面几何测量中的图像畸变校正

苏成志; 王恩国; 郝江涛; 曹国华; 徐洪吉

doi:10.3788/OPE.20111901.0161

您当前的位置：

首页 >

文章列表页 >

平面几何测量中的图像畸变校正

信息科学 | 更新时间：2020-08-12

- 平面几何测量中的图像畸变校正
- Distortion correction for images in planar metrology
- 光学精密工程 2011年19卷第1期页码：161-167
- 作者机构：
  
  长春理工大学机电工程学院,吉林长春,130022
- 作者简介：
- 基金信息：
  
  吉林省科技发展计划基金资助项目(No.20070304)()
- DOI：10.3788/OPE.20111901.0161
  中图分类号： TP391.4
- 收稿日期：2009-11-26，
  
  修回日期：2010-03-29，
  
  网络出版日期：2011-01-22，
  
  纸质出版日期：2011-01-22
- 稿件说明：
移动端阅览
苏成志, 王恩国, 郝江涛, 曹国华, 徐洪吉. 平面几何测量中的图像畸变校正[J]. 光学精密工程, 2010,19(1): 161-167

SU Cheng-zhi, WANG En-guo, HAO Jiang-tao, CAO Guo-hua, XU Hong-ji. Distortion correction for images in planar metrology[J]. Editorial Office of Optics and Precision Engineering, 2010,19(1): 161-167
苏成志, 王恩国, 郝江涛, 曹国华, 徐洪吉. 平面几何测量中的图像畸变校正[J]. 光学精密工程, 2010,19(1): 161-167 DOI： 10.3788/OPE.20111901.0161.

SU Cheng-zhi, WANG En-guo, HAO Jiang-tao, CAO Guo-hua, XU Hong-ji. Distortion correction for images in planar metrology[J]. Editorial Office of Optics and Precision Engineering, 2010,19(1): 161-167 DOI： 10.3788/OPE.20111901.0161.

摘要

针对图像畸变对平面图像几何线度精密测量精度的影响

提出一种直接利用标准网格板作为测量基准的畸变校正方法。根据待测物体与网格板处于相同物面时

其图像畸变与网格板图像畸变相同

待测点在网格板图像中相对网格的几何位置不变这一性质

提出直接使用发生畸变的网格板图像作为校正基准来代替通过建模将外部标准转换为摄像机内部基准的畸变校正思路。首先

确定待测点在网格板畸变图像中的初始位置;然后

根据平行线分线段成比例定理确定待测点在网格板畸变图像网格内的精确位置

对两者求和完成待测物体上任意两点的实际几何线度测量。实验证明

当校正网格板间距为1 mm

精度为0.2 m时

使用提出方法得到的畸变误差是现有校正方法的20%

校正精度可达4 m。该方法省去了建模过程

其校正精度仅与网格板精度有关

具有更高的精度和适应性。

Abstract

In consideration of the effect of the distortion error of an image on the accuracy of planar geometrical measurement in the precise visual metrology

a method to correct the image distortion by using standard grid board directly as measurement calibration is proposed. As the position of an under-tested point is unchanged relative to that of grid board when an under-tested object and a grid board lay on the same object plane

the grid board is directly used as the correcting calibration of image distortion instead of the way that converts the external standard into the intrinsic parameter of a camera by modeling .Firstly

the primary position of the under-tested point in the image of grid board is determined;then

its fine distance is decided according to the proportion theorem of line segment divided by parallel line.Finally

planar geometrical measurement is fulfilled by calculating the sum of both distances.Experimental results show that the distortion error by the proposed method has reduced to 20% that of the traditional method and the correctoin accuracy of image has reached 4 m or higher

while the distance of intersection point of the calibrated grid board is 1 mm and its accuracy is 0.2 m.The method is more applicable and has high accuracy

for it omits the modeling and its accuracy only depends on the calibrated grid board.

关键词

Keywords

references

SMITH W, VAKIL N, MAISLIN S.Correction of distortion in endoscope images [J]. IEEE Trans Med Imaging,1992,11(1):117-122.[2] HANEISHI H,YAGIHASHI Y,MIYAKE Y.A new method for distortion correction of electronic endoscope images[J].IEEE Trans.Med.Imaging, 1995,14(3):548-555.[3] 刘航,郁道银,杜吉,等. 广角成像系统光学畸变的数字校正方法[J]. 光学学报, 1998,18(8):1108-1112. LIU H,YU D Y,DU J,et al.. Distortion correction of the wide-angle optical system with digital technology[J]. Acta Optica Sinica, 1998,18(8):1108-1112.(in Chinese)[4] 行麦玲,刘贱平,林家明,等. 大视场短焦距镜头CCD摄像系统的畸变校正[J]. 光学技术,2003,29(3):377-379. XING M L,LIU J P,LIN J M,et al.. Distortion measurement of CCD camera with a large-field short focal length len[J].Optical Technique,2003,29(3):377-379. (in Chinese)[5] 史泽林,康娇,孙锐. 基于BP神经网络的大视场成像畸变校正方法[J]. 光学精密工程,2005,13(3):348-353. SHI Z L,KANG J,SUN R. BP NN-based method for lens distortion correction of large-field imagin[J].Opt. Precision Eng., 2005,13(3):348-353. (in Chinese)[6] 牛建军,刘上乾,姚荣辉. 高准确度光电成像测量系统图象畸变校正算法[J]. 光子学报, 2006,35(9):1317-1320. NIU J J,LIU SH Q, YAO R H. Algorithm for image correction in high precision imaging measurement system[J]. Acta Photonica Sinica, 2006,35(9):1317-1320. (in Chinese)[7] 凌伟,王志乾,高峰端. 光电测量系统畸变的实时数字校正[J]. 光学精密工程, 2007,15(2):277-282. LING W, WANG Z Q,GAO F D.Real time digital correction for distortion in photoelectronical measuring system[J]. Opt. Precision Eng., 2007,15(2):277-282. (in Chinese)[8] 吴国栋. 离轴三反光学镜头像面畸变的标定方法[J]. 光学精密工程,2008,16(11):2127-2131. WU G D, Calibration of distortion for three-mirror off-axis[J]. Opt. Precision Eng., 2008,16(11):2127-2131. (in Chinese)[9] 梁冬泰,王宣银. 基于分块的摄像机内外参数标定方法[J]. 上海交通大学学报,2009,43(3):422-426. LIANG D T,WANG X Y.Partition-based camera intrinsic and extrinsic parameters calibration for planar visual metrology[J].Journal of Shanghai Jiaotong University, 2009,43(3):422-426. (in Chinese)[10] JIU X H , ANSHUMAN R.Geometric calibration of digital cameras for 3D cumulus cloud measurements[J]. Journal of Atmospheric and Oceanic Technology, 2009, 26:200-214.[11] 兰海滨,王平,龙腾. 图像拼接中相机镜头非线性畸变的校正[J]. 光学精密工程,2009,17(5):1197-1202. LAN H B,WANG P,LONG T.Nonlinear aberration correction of lens in image mosai[J]. Opt. Precision Eng., 2009,17(5):1197-1202. (in Chinese)

浏览量

387

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

发散扫描模式下OCT图像畸变分析与矫正

结合图像内容匹配的机器人视觉导航定位与全局地图构建系统

共振扫描显微成像中的图像畸变校正

高速大扫描范围原子力显微镜系统的设计

压印对正系统中标记图像几何畸变的校正