CCD分段测量的光学位移测量系统

李雅倩; 付献斌; 周坤

doi:10.3788/OPE.20111909.2036

您当前的位置：

首页 >

文章列表页 >

CCD分段测量的光学位移测量系统

现代应用光学 | 更新时间：2020-08-12

- CCD分段测量的光学位移测量系统
- Optical displacement measuring system by CCD segmental measurement
- 光学精密工程 2011年19卷第9期页码：2036-2042
- 作者机构：
  
  燕山大学电气工程学院,河北秦皇岛,066004
- 作者简介：
- 基金信息：
  
  国家科技重大专项资助项目(No. 2010ZX04017-013)()
- DOI：10.3788/OPE.20111909.2036
  中图分类号： TH822;TN386.5
- 收稿日期：2011-01-14，
  
  修回日期：2011-03-18，
  
  网络出版日期：2011-09-26，
  
  纸质出版日期：2011-09-26
- 稿件说明：
移动端阅览
李雅倩, 付献斌, 周坤. CCD分段测量的光学位移测量系统[J]. 光学精密工程, 2011,19(9): 2036-2042

LI Ya-qian, FU Xian-bin, ZHOU Kun. Optical displacement measuring system by CCD segmental measurement[J]. Editorial Office of Optics and Precision Engineering, 2011,19(9): 2036-2042
李雅倩, 付献斌, 周坤. CCD分段测量的光学位移测量系统[J]. 光学精密工程, 2011,19(9): 2036-2042 DOI： 10.3788/OPE.20111909.2036.

LI Ya-qian, FU Xian-bin, ZHOU Kun. Optical displacement measuring system by CCD segmental measurement[J]. Editorial Office of Optics and Precision Engineering, 2011,19(9): 2036-2042 DOI： 10.3788/OPE.20111909.2036.

摘要

为了高精度地实现大量程的位移测量

采用传统激光三角法的测量原理

提出一种基于虚拟探测器的激光三角法来测量位移。该方法基于3个CCD分段测量的思想

将3个CCD互相独立且沿光轴均匀分布

以此扩大传统方法测量的范围。使用平面反射镜作为虚拟探测器进行探测

当成像光束经平面镜反射后在CCD上成像时

系统相当于增加了一个CCD

扩展了测量量程。由准直系统、偏振片、光阑组成准直滤光系统

缩小探测器光敏面上像点的直径

减小被测表面非理想光点对测量精度的影响

从而实现了较高精度下的大位移测量。最后通过实验验证了方法的可行性。

Abstract

To realize the large-scale and high-precision displacement measurement

a new method based on a virtual detector was described according to the basic principles of traditional laser triangulation method. The CCD subsection measurement was used to enlarge the measuring range and to implement the displacement measurement. Three independent CCDs were distributed uniformly along the optical axis and a plain reflected mirror was regarded as the virtual detector.When the beam image was reflected by the plane mirror

the beam was imaged by CCDs. The designed system is equivalent to that a CCD is added

therefore

the measuring range is enlarged. Furthermore

the collimator filter is composed of a collimation system

a polarizer and a diaphragm. It shortens the diameter of the image spots on the photosensitive surface of the detector

and reduces the influent of unideal optical spots on the measured surface on the measuring accuracy.The high-precision measurement of large displacement is achieved. The results are in agreement with the experimental observation.

关键词

Keywords

references

刘维,韩旭东,艾华. 激光三角法在位移测量中的应用[J].2004,12(4):104-107. LIU W, HAN X D,AI H.Application of laser triangulation in displacement measurement[J]. 2004, 12(4):104-107. (in Chinese)[2] 谭海艳,赵小军. 基于激光三角法的零件表面粗糙度在线测量[J]. 机床与液压,2010,38(6):67-68. TAN H Y, ZHAO X J. Surface roughness real time measurement method of parts based on laser triangulation[J]. Machine Tool & Hydraulics,2010,38(6):67-68. (in Chinese)[3] 徐万和,李忠新,吴志林,等. 基于激光三角测量原理的自动机运动测试方法[J]. 测试技术学报,2010,24(3): 215-218. XU W H,LI ZH X,WU ZH L, et al.. Motion test method based on laser triangulation measurement principle for automatic mechanism[J]. Journal of Test and Measurement Technology, 2010,24(3):215-218. (in Chinese)[4] SHIOU F J,LIU M X.Development of a novel scattered triangulation laser probe with six linear charge-coupled devices (CCDs) [J]. Optics and Lasers in Engineering, 2009,47(1):7-18.[5] 刘君,刘江春,晏克俊. 光学三角法高精度自动调焦系统设计[J]. 西安理工大学学报,2004,20(1):63-66. LIU J, LIU J C, YAN K J. Design of high precision automatic focusing system based on method of optic triangle[J].Journal of Xi'an University of Technology, 2004,20(1):63-66. (in Chinese)[6] 黄战华,蔡怀宇,李贺桥,等. 三角法激光测量系统的误差分析及消除方法[J]. 光电工程,2002,29(3): 58-61. HUANG ZH H,CAI H Y,LI H Q, et al.. Analysis for error in triangular laser measurement system and an elimination method[J].Opto-electronic Engineering, 2002,29(3): 58-61. (in Chinese)[7] 史亚莉,高云国,张磊,等. 提高CCD激光自准直测角精度的硬件方法[J]. 光学精密工程, 2008,16(4):726-732. SHI Y L,GAO Y G,ZHANG L, et al..Improvement of measuring accuracy of CCD laser autocollimator by changing hardware parameters[J].Optics and Precision Engineering, 2008,16(4):726-732. (in Chinese)[8] 陈洪芳,钟志,丁雪梅. 激光外差干涉的非线性误差补偿[J]. 光学精密工程, 2010,18(5):1043-1047. CHEN H F, ZHONG ZH,DING X M. Compensation of nonlinear errors in laser heterodyne interferometers[J]. Optics and Precison Engineering, 2010, 18(5):1043-1047. (in Chinese)[9] 高学海,徐科军,张瀚,等. 基于单目视觉和激光测距仪的位姿测量算法[J]. 仪器仪表学报,2007,28(8):1479-1485. Gao X H,XU K J, ZHANG H, et al.. Position-pose measurement algorithm based on single camera and laser range-finder[J].Chinese Journal of Scientific Instrument,2007,28(8):1479-1485. (in Chinese)[10] 雷琳君,杨燕,陈卫标. 星载激光测距仪的高精度时间间隔测量单元[J]. 中国激光,2007, 34(10):1422-1426. LEI L J, YANG Y,CHEN W B.High-accuracy time-interval-unit for space borne laser range finder[J]. Chinese Journal of Lasers,2007, 34(10): 1422-1426. (in Chinese)[11] 曾宪阳,张志良. PSD激光三角法弱反射微振动测量系统[J]. 浙江师范大学学报(自然科学版),2009,32(3):298-302. ZENG X Y, ZHANG ZH L.A system measuring micro vibration in weak reflection based on PSD and laser triangulation method[J]. Journal of Zhejiang Normal University(Natural Sciences), 2009,32(3):298-302. (in Chinese)[12] QI L T, NAMBA Y. Precision laser adjustment using CW diode laser[J]. Precision Engineering, 2011,35(1): 126-132.[13] ALFREDO C, FEDERICO M, STEFANO M, et al.. Laser-triangulation device for in-line measurement of road texture at medium and high speed[J].Mechanical Systems and Signal Processing,2010,24(7):2225-2234.[14] 张维光,赵宏,张琦,等. 线结构光三维轮廓测量系统的标定方法[J]. 中国激光,2009,36(1):182-188. ZHANG W G, ZHAO H, ZHANG Q, et al..Calibration method for three-dimensional measurement system based on linear-structure light[J]. Chinese Journal of Lasers, 2009,36(1):182-188. (in Chinese)[15] 林玉池,张晓玲,牛小兵,等. 基于虚拟相位靶标的光栅投影三维测量系统标定[J]. 光电子激光,2005,16(5):591- 595. LIN Y CH,ZHANG X L,NIU X B, et al.. Calibration method for grating projection profilometry system using virtual phase calibrating model plane[J]. Journal of Optoelectronics Laser, 2005,16(5):591-595.(in Chinese)

浏览量

670

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

基于卡尔曼滤波的激光外差干涉位移测量误差补偿

超精密空间分离式外差利特罗平面光栅编码器位移测量系统

面向浸没式光刻机的超精密光学干涉式光栅编码器位移测量技术研究综述

用于高精度测量位移等参量的光纤多波长激光器

面向浸没式光刻机的超精密光学干涉式光栅编码器位移测量技术综述