具有三层结构的SU-8胶V形微电热驱动器

张然; 褚金奎; 王海祥; 陈兆鹏

doi:10.3788/OPE.20122007.1500

您当前的位置：

首页 >

文章列表页 >

具有三层结构的SU-8胶V形微电热驱动器

微纳技术与精密机械 | 更新时间：2020-08-12

- 具有三层结构的SU-8胶V形微电热驱动器
- SU-8 chevron electrothermal micro-actuator with three-layer structures
- 光学精密工程 2012年20卷第7期页码：1500-1508
- 作者机构：
  
  大连理工大学机械工程学院,辽宁大连,116024
- 作者简介：
- 基金信息：
  
  国家973重点基础研究发展计划资助项目(No.2011CB302101)()
- DOI：10.3788/OPE.20122007.1500
  中图分类号： TH112.5;TH703.6
- 收稿日期：2012-03-02，
  
  修回日期：2012-05-11，
  
  网络出版日期：2012-07-10，
  
  纸质出版日期：2012-07-10
- 稿件说明：
移动端阅览
张然, 褚金奎, 王海祥, 陈兆鹏. 具有三层结构的SU-8胶V形微电热驱动器[J]. 光学精密工程, 2012,20(7): 1500-1508

ZHANG Ran, CHU Jin-kui, WANG Hai-xiang, CHEN Zhao-peng. SU-8 chevron electrothermal micro-actuator with three-layer structures[J]. Editorial Office of Optics and Precision Engineering, 2012,20(7): 1500-1508
张然, 褚金奎, 王海祥, 陈兆鹏. 具有三层结构的SU-8胶V形微电热驱动器[J]. 光学精密工程, 2012,20(7): 1500-1508 DOI： 10.3788/OPE.20122007.1500.

ZHANG Ran, CHU Jin-kui, WANG Hai-xiang, CHEN Zhao-peng. SU-8 chevron electrothermal micro-actuator with three-layer structures[J]. Editorial Office of Optics and Precision Engineering, 2012,20(7): 1500-1508 DOI： 10.3788/OPE.20122007.1500.

摘要

为解决SU-8胶微电热驱动器在工作过程中存在平面外运动的问题

提出了一种具有铜-SU-8胶-铜三层对称结构的新型SU-8胶V形微电热驱动器。采用刚度矩阵方法建立了包含被驱动结构刚度的微电热驱动器力学模型

并针对一种柔性微夹钳

利用该模型对微电热驱动器进行了几何参数设计。利用Ansys仿真软件对所设计微驱动器进行了分析

仿真结果验证了所建模型的合理性。提出了一种新的MEMS加工工艺来制作三层结构微电热驱动器

并测试了它的性能。结果表明

实验结果与仿真结果相差不大

在150 mV驱动电压下

所设计微驱动器温度仅升高约32.93°C

并对微夹钳产生约2.5 μm的输入位移

使微夹钳产生126 μm的钳口距离改变量。微驱动器仅消耗大约30.35 mW的功率

钳口的平面外运动小于500 nm。最后

利用微电热驱动器驱动的微夹钳成功地对一个长1.2 mm

宽135 μm

厚50 μm的SU-8胶材料微型零件进行了微操作实验

实验证明了微驱动器实际性能基本满足设计要求。

Abstract

To eliminate the out-of plane actuation of a SU-8 electrothermal micro-actuator

a novel SU-8 chevron electrothermal micro-actuator with a copper/SU-8/copper symmetrical structure was proposed. The mechanical model of the micro-actuator which contains the stiffness of a driven structure was established by using the stiffness matrix method. The geometric parameters of the micro-actuator were designed for a microgripper by using the established model. The designed micro-actuator was simulated by Ansys software and the simulation results verified the reasonability of the mechanical model. Then

the micro-actuator and the microgripper were fabricated by a simple process followed with a performance test. The test results show that when the temperature of the micro-actuator only increases 32.93℃ in a driving voltage of 150 mV

the output displacement is 2.5 μm and jaw gap change is 126 μm. During the operation processes

the out-of plane displacement of the tip is always lower than 500 nm. Finally

the micro-manipulation sequence of a SU-8 micro-part with a size of 1.4 mm×135 μm×50 μm was carried out to verify the driving ability of the micro-actuator.

关键词

Keywords

references

陈立国,刘柏旭. 复合式MEMS微夹持器的研制 [J].光学精密工程,2009,17(8):1928-1934. CHEN L G, LIU B X. Development of hybrid-type MEMS microgripper[J]. Opt. Precision Eng., 2009,17(8): 1928-1934. (in Chinese)

王代华,朱炜. WTYD型压电陶瓷微位移器的迟滞特性;建模与实验验证 [J].光学精密工程,2010,18(1):205-211. WANG D H,ZHU W. Hysteretic modeling and experimental verification for WTYD type piezoceramic micro-actuators[J]. Opt. Precision Eng., 2010,18(1):205-211 (in Chinese).

李路明,王立鼎. SMA微夹钳的研究 [J].光学精密工程,1997,5(2):37-42. LI L M,WANG L D. Study on SMA Microclamp[J]. Opt. Precision Eng., 1997,5(2):37-42. (in Chinese)

KARIN N A, KENNETH C, DIRCH H P, et al.. Electrothermal microgrippers for pick-and-place operations[J]. Microelectron. Eng., 2008, 85(5-6):1128-1130.

HOXHOLD B, BUTTGENBACH S. Easily manageable, electrothermally actuated silicon micro gripper[J]. Microsyst.Technol, 2010,16(8-9):1609-1617.

张立国,陈迪,杨帆,等. SU-8胶光刻工艺研究 [J].光学精密工程,2002,10(3):266-269. ZHAN L G, CHEN D, YANG F, et al.. Research on SU-8 resist photolithography process[J]. Opt. Precision Eng., 2002,10(3):266-269. (in Chinese)

黄新龙,熊瑛,陈光焱,等. UV-LIGA技术制作微型螺旋形加速度开关 [J].光学精密工程,2010,18(5):1152-1158. HUANG X L, XIONG Y, CHEN G Y, et al.. Fabrication of micro spiral acceleration switch using UV-LIGA technology[J]. Opt. Precision Eng., 2010,18(5):1152-1158. (in Chinese).

CHRONIS N, LEE L P. Electrothermally activated SU-8 microgripper for single cell manipulation in Solution[J]. J. Microelectromech. Syst, 2005, 14(4):857-863.

COLINJIVADI K S, LEE J B, DRAPER R. Viable cell handling with high aspect ratio polymer chopstick gripper mounted on a nano precision manipulator[J]. Microsyst.Technol, 2008,14(9-11):1626-1633.

KOSEKI Y, TANIKAWA T, KOYACHI N, et al.. Kinematic analysis of a translational 3-d of. micro-parallel mechanism using the matrix method[J]. Adv. Robot, 2002,16 (3) :251-264.

PARK S R, YANG S H. A mathematical approach for analyzing ultra precision positioning system with compliant mechanism[J]. J. Mater. Process. Technol, 2005,(164-165):1584-1589.

浏览量

333

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

大型二维多折展开平面天线机构设计及动力学特性分析

软X射线光发射电子显微镜光束线聚焦用KB镜系统

上海光源前端高热负载挡光器的结构设计与优化

V型直线超声电机梁式夹持的结构设计

三维测量工业内窥镜的双目光学系统