双柔性支撑板快速伺服刀架优化设计及测试

周京博; 孙涛; 侯国安

doi:10.3788/OPE.20132102.0349

您当前的位置：

首页 >

文章列表页 >

双柔性支撑板快速伺服刀架优化设计及测试

微纳技术与精密机械 | 更新时间：2020-08-12

- 双柔性支撑板快速伺服刀架优化设计及测试
- Optimal design and test of double elastic plate based fast tool servo
- 光学精密工程 2013年21卷第2期页码：349-355
- 作者机构：
  
  哈尔滨工业大学精密工程研究所
- 作者简介：
- 基金信息：
  
  高等学校学科创新引智计划资助项目(B14013)
- DOI：10.3788/OPE.20132102.0349
  中图分类号： TH122.1;TG51
- 收稿日期：2012-07-03，
  
  修回日期：2012-10-15，
  
  网络出版日期：2013-02-23，
  
  纸质出版日期：2013-02-15
- 稿件说明：
移动端阅览
周京博孙涛侯国安. 双柔性支撑板快速伺服刀架优化设计及测试[J]. 光学精密工程, 2013,21(2): 349-355

ZHOU Jing-bo SUN Tao HOU Zhen-an. Optimal design and test of double elastic plate based fast tool servo[J]. Editorial Office of Optics and Precision Engineering, 2013,21(2): 349-355
周京博孙涛侯国安. 双柔性支撑板快速伺服刀架优化设计及测试[J]. 光学精密工程, 2013,21(2): 349-355 DOI： 10.3788/OPE.20132102.0349.

ZHOU Jing-bo SUN Tao HOU Zhen-an. Optimal design and test of double elastic plate based fast tool servo[J]. Editorial Office of Optics and Precision Engineering, 2013,21(2): 349-355 DOI： 10.3788/OPE.20132102.0349.

摘要

设计了一种基于双柔性支承板的快速伺服刀架用于金刚石车削加工非回转对称微结构表面，并对其性能进行了测试。根据约束条件推导了刀架柔性支承板的刚度解析表达式，同时给出了柔性板上最大Von Mises应力的计算公式。根据快速伺服刀架设计指标，优化了柔性支承板的结构参数，并根据上述结构参数，加工得到了快速伺服刀架。最后，搭建了快速伺服刀架控制系统，测试了它的静态及动态特性。测试结果表明，设计的快速伺服刀架的刚度为53 N/μm，最小运动分辨率为3 nm，工作行程可达20 μm。另外，它的稳态跟踪误差小于4 nm，开环带宽为2 kHz，一阶固有频率可达3 kHz。测试结果不仅验证了所述设计方法的正确性，也表明采用双柔性支承板结构是设计高刚度、高精度微位移机构的一种有效方法。

Abstract

A double elastic plate based Fast Tool Servo (FTS) was designed to fabricate non-rotational symmetrical micro-structured surfaces using diamond turning method. Then

the performance of the FTS was tested. According to constrain conditions

the analytical expression for the stiffness of elastic plates was derived and the calculation method for the maximum Von Mises stress of the plates was also given. Based on the specification of the FTS

the structural parameters of the elastic plates were optimized and a FTS was machined in accordance with the parameters mentioned above. Finally

a control system for the FTS was established

and the static and dynamic characters were tested. The test results show that the stiffness of the FTS is 53 N/μm

the motion resolution is 3 nm

and the travel range can reach to 20 μm. Furthermore

the FTS can offer the static following error better than 4 nm

the open loop bandwidth of 2 kHz and the fundamental frequency up to 3 kHz. The test results not only demonstrate the correctness of the design method

but also indicate that the double elastic plate based structure is a good choice for the micro-displacement units with high stiffness and high precision.

关键词

Keywords

references

李荣彬, 张志辉, 杜雪, 等. 微结构光学元件快速伺服刀架加工技术研究[J]. 纳米技术与精密工程, 2005, 3(3):216-221.LI R B, ZHANG ZH H, DU X, et al.. An investigation of fast tool servo machining of optical microstructures [J]. Nanotechnology and Precision Engineering,2005, 3(3):216-221. (in Chinese)[2]杨帆, 杨海宽, 陈志华, 等. 音圈式快速伺服刀架的分析与设计[J].国防科技大学学报, 2009, 31(4):42-47.YANG F, YANG H K, CHEN ZH H, et al.. Analysis and design of voice-coil actuator used in fast tool servo [J].　Journal of National University of Defense Technology, 2009, 31(4):42-47. (in Chinese)[3]MONTESANTI R C, TRUMPER D L. A 10 kHz short-stroke rotary fast tool servo [C].American Society for Precision Engineering 2004 Annual Meeting, Orlando: ASPE, 2004:206609.[4]PATTERSON S R, MAGRAB E B. Design and testing of a fast tool servo for diamond turning [J]. Precision Engineering, 1985, 7 (3):123-128.[5]OKAZAKI Y. A Micro-positioning tool post using a piezoelectric actuator for diamond turning machines [J]. Precision Engineering,1990,12(3):151-156.[6]GAO W, ARAKI T, KIYONO S, et al.. Precision nano-fabrication and evaluation of a large area sinusoidal grid surface for a surface encoder [J]. Precision Engineering, 2003, 27(3):289-298.[7]BRINKSMEIERA E, RIEMERA O, GLABEA R, et al.. Submicron functional surfaces generated by diamond machining [J]. CIRP Annals - Manufacturing Technology, 2010, 59(1):535-538.[8]戴一凡, 杨海宽, 王贵林, 等. 压电陶瓷驱动的超精密快刀伺服系统的设计与研制[J]. 中国机械工程, 2009, 20(22):2717-2721.DAI Y F，YANG H K, WANG G L, et al.. Design and development of an ultra- precision fast tool servo system driven by piezoelectric ceramic [J]. China Mechanical Engineering, 2009, 20(22):2717-2721. (in Chinese)[9]YANG Y H, CHEN S J, HUO D H, et al.. Performance analysis and optimal design of fast tool servo used for machining micro-structured surfaces [J]. Proceedings of the Institution of Mechanical Engineers, Part C Journal of Mechanical Engineering Science, 2008, 222: 1541-1546.[10]MA H Q, HU D J, ZHANG K. A fast tool feeding mechanism using piezoelectric actuators in noncircular turning [J]. International Journal of Advanced Manufacturing Technology, 2005, 27 (3/4):254-259.[11]LIU Q，ZHOU X Q，XU P Z，et al.. A flexure-based long-stroke fast tool servo for diamond turning [J]. The International Journal of Advanced Manufacturing Technology, 2012, 59(9-12):859-867.[12]KIMA H S, LEE K I, LEE K M, et al.. Fabrication of free-form surfaces using a long-stroke fast tool servo and corrective figuring with on-machine measurement [J]. International Journal of Machine Tools and Manufacture, 2009, 49(12-13):991-997.[13]PRECITECH. Fast Tool Servo [EB/OL]. [2012-05-12]. http://www.precitech.com/machine-applications/fast- tool-servo.[14]LOBONTIU N. Compliant mechanisms: design of flexure hinges [M]. CRC Press Inc., 2002.[15]吴家龙. 弹性力学[M]. 北京：高等教育出版社，2001.WU J L. Elasticity [M]. Beijing: Higher Education Press, 2001. (in Chinese)

浏览量

624

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

面向在轨装配的冗余索并联机构变刚度控制

变截面节流器对空气静压轴承承载性能的影响

(2PRR)²+R平面并联机构的刚度与固有频率

双柔性平行六连杆微动平台结构的设计及测试

光学自由曲面快速刀具伺服车削误差的补偿