锥束CT圆轨迹半覆盖扫描的几何校正

张峰; 江桦; 闫镔; 魏星; 李磊

doi:10.3788/OPE.20132107.1659

您当前的位置：

首页 >

文章列表页 >

锥束CT圆轨迹半覆盖扫描的几何校正

现代应用光学 | 更新时间：2020-08-12

- 锥束CT圆轨迹半覆盖扫描的几何校正
- Geometric calibration for half-cover scanning in circular cone-beam CT
- 光学精密工程 2013年21卷第7期页码：1659-1665
- 作者机构：
  
  信息工程大学信息系统工程学院,河南郑州,450002
- 作者简介：
- 基金信息：
  
  国家高技术发展计划项目()
- DOI：10.3788/OPE.20132107.1659
  中图分类号： TP391.4
- 收稿日期：2013-01-22，
  
  修回日期：2013-03-26，
  
  网络出版日期：2013-07-15，
  
  纸质出版日期：2013-07-15
- 稿件说明：
移动端阅览
张峰江桦闫镔魏星李磊. 锥束CT圆轨迹半覆盖扫描的几何校正[J]. 光学精密工程, 2013,21(7): 1659-1665

. Geometric calibration for half-cover scanning in circular cone-beam CT[J]. Editorial Office of Optics and Precision Engineering, 2013,21(7): 1659-1665
张峰江桦闫镔魏星李磊. 锥束CT圆轨迹半覆盖扫描的几何校正[J]. 光学精密工程, 2013,21(7): 1659-1665 DOI： 10.3788/OPE.20132107.1659.

. Geometric calibration for half-cover scanning in circular cone-beam CT[J]. Editorial Office of Optics and Precision Engineering, 2013,21(7): 1659-1665 DOI： 10.3788/OPE.20132107.1659.

摘要

研究了一种高精度的几何校正方法用于对锥束CT圆轨迹半覆盖成像进行几何校正。首先，使用Otsu算法分割体模投影中钢球所在的区域，并计算质心坐标。然后，采用最小二乘算法对质心进行椭圆拟合，并根据椭圆参数采用Cho的全覆盖几何校正算法计算探测器的旋转角度。最后，顺时针旋转质心，求得旋转的角度后，再次进行椭圆拟合，并根据得到的椭圆参数采用Noo的全覆盖几何校正算法计算除探测器倾斜角之外的所有几何参数。实验结果表明：探测器旋转角和偏转角的测量精度分别为0.02和0.01；射线源到探测器和到旋转轴的距离的测量精度分别为0.05 mm和0.01 mm；射线源在探测器上投影坐标的计算精度分别为0.07 mm和0.15 mm。由得到的结果可知，所提出的校正方法有效地去除了几何伪影的干扰，满足半覆盖成像图像重建的要求。

Abstract

A highprecision method was investigated to realize the geometric calibration of halfcover scanning in circular conebeam Computed Tomography (CT). First

projected areas of steel balls were segmented from the background by using the Otsus method

and the mass centers of balls were calculated. Then

the elliptic functions for mass centers were fitted by the leastsquare algorithm

and the rotation angle of detector was determined by Chos geometric calibration method for circular scanning. Finally

the rotated mass centers were fitted as two ellipses

and the rest geometric parameters except the tilted angle of detector were calculated by using Noos geometric calibration method for circular scanning. Experimental results indicate that the measuring precisions of rotation angle and skew angle for the detector are 0.02 and 0.01

respectively

the measuring precisions of sourcedetectordistance and sourceobjectdistance are 0.05 mm and 0.01 mm

respectively; and the calculating precisions of orthogonal projection coordinates of source are 0.07 mm and 0.15 mm. The proposed method depress the geometric artifacts significantly

and can satisfy the demands of highprecision image reconstruction.

关键词

Keywords

references

NOO F, CLACKDOYLE R, MENNESSIER C, et al.. Analytic method based on identification of ellipse parameters for scanner calibration in cone-beam tomography [J]. Physics in Medicine and Biology, 2000, 45(11): 3489-3508.[2]CHO Y, MOSELEY D J, SIEWERDSEN J H, et al.. Accurate technique for complete geometric calibration of cone-beam computed tomography systems[J]. Medical Physics, 2005, 32(4): 968-983.[3]WU D F, LI L, ZHANG L, et al.. Geometric calibration of cone-beam CT with a flat-panel detector\[C\]. IEEE Nuclear Science Symposium Conference, Valencia, Spain: NSS/MIC, 2011: 2952-2955.[4]KYRIAKOU Y, LAPP R M, HILLEBRAND L, et al.. Simultaneous misalignment correction for approximate circular cone-beam computed tomography[J]. Physics in Medicine and Biology, 2008, 53(22): 6267-6289.[5]李保磊, 张耀军. X射线CT系统投影旋转中心的测量[J]. 光学精密工程, 2011, 19(5): 967-971. LI B L, ZHANG Y J. Measurement of center of rotation for projection in X-ray computed tomographic system [J]. Opt. Precision Eng., 2011, 19(5): 967-971. (in Chinese)[6]FELDKAMP L, DAVIS L C , KRESS J W. Practical cone-beam algorithm [J]. Journal of the Optical Society America A, 1984, 1(6): 612-619.[7]TUY H K. An inversion formula for cone-beam reconstruction [J]. SIAM Journal on Applied Mathematics, 1983, 43(3): 546-552.[8]刘丰林, 乔桂锋, 邹斌. 工业CT图像圆精确测量[J]. 光学精密工程, 2009, 17(11): 2842-2848.LIU F L, QIAO G F, ZOU B. Precise measurement of circles in industrial computed tomographic images[J]. Opt. Precision Eng., 2009, 17(11): 2842-2848. (in Chinese)[9]陶李, 王珏, 邹永宁, 等．改进的Zernike矩工业CT图像边缘检测[J]. 中国光学, 2012, 5(1): 48-56.TAO L, WANG J, ZOU Y N, et al.. Improved Zernike moment method for industrial CT image edge detection [J]. Chinese Optics, 2012, 5(1): 48-56. (in Chinese)[10]邹晓兵, 曾理．锥束螺旋CT半覆盖扫描重建[J]. 光学精密工程, 2010, 18(2): 434-442.ZOU X B, ZENG L. Half-cover scanning and reconstructing for helical cone-beam CT[J]. Opt. Precision Eng., 2010, 18(2): 434-442. (in Chinese)[11]LI L, CHEN Z Q, ZHANG L, et al.. A cone-beam tomography system with a reduced size planar detector: a backprojection-filtration reconstruction algorithm as well as numerical and practical experiments[J]. Applied Radiation and Isotopes, 2007, 65(9): 1041-1047.[12]OTSU N. A threshold selection method from gray-level histogram[J]. IEEE Transactions on Systems, Man and Cybernetic, 1979, 9(1): 62-66.[13]杨民, 刘静华, 李保磊, 等. 三维显微CT扫描系统的X射线源焦点投影坐标测量方法[J]. 光学学报, 2009, 29(5): 1275-1280. YANG M, LIU J H, LI B L, et al.. Measurement method of X-ray focus projection coordinates of three-dimensional micro-computerized tomography scanning system[J]. Acta Optica Sinica, 2009, 29(5): 1275-1280. (in Chinese)[14]GUO J Q, ZENG L, ZOU X B. An improved half-covered helical cone-beam CT reconstruction algorithm based on localized reconstruction filter[J]. Journal of X-Ray Science and Technology, 2011, 19(3): 293-312.

浏览量

228

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

联合全局与局部特征的深度压缩感知图像重构

基于分数匹配生成模型的无透镜成像方法

Res2-Unet深度学习网络的RGB-高光谱图像重建

基于最小二乘正则相关性分析的颅骨身份识别

混合高斯/泊松最大似然函数下的CBCT图像重建