超高真空精密四刀狭缝的结构原理及有限元分析

高飒飒; 卢启鹏; 彭忠琦; 龚学鹏

doi:10.3788/OPE.20132107.1741

您当前的位置：

首页 >

文章列表页 >

超高真空精密四刀狭缝的结构原理及有限元分析

微纳技术与精密机械 | 更新时间：2020-08-12

- 超高真空精密四刀狭缝的结构原理及有限元分析
- Principle and finite element analysis on UHV four-knife precision slits
- 光学精密工程 2013年21卷第7期页码：1741-1747
- 作者机构：
  
  1. 中国科学院大学北京,中国,100049
  2. 中国科学院长春光学精密机械及物理研究所应用光学国家重点实验室,吉林长春,130033
- 作者简介：
- 基金信息：
  
  极高分辨变包含角平面光栅单色器关键技术及检测方法研究();第三代同步辐射光学元件压弯装置机理研究()
- DOI：10.3788/OPE.20132107.1741
  中图分类号： TH744.1
- 收稿日期：2012-07-10，
  
  修回日期：2012-08-29，
  
  网络出版日期：2013-07-15，
  
  纸质出版日期：2013-07-15
- 稿件说明：
移动端阅览
高飒飒卢启鹏彭忠琦龚学鹏. 超高真空精密四刀狭缝的结构原理及有限元分析[J]. 光学精密工程, 2013,21(7): 1741-1747

. Principle and finite element analysis on UHV four-knife precision slits[J]. Editorial Office of Optics and Precision Engineering, 2013,21(7): 1741-1747
高飒飒卢启鹏彭忠琦龚学鹏. 超高真空精密四刀狭缝的结构原理及有限元分析[J]. 光学精密工程, 2013,21(7): 1741-1747 DOI： 10.3788/OPE.20132107.1741.

. Principle and finite element analysis on UHV four-knife precision slits[J]. Editorial Office of Optics and Precision Engineering, 2013,21(7): 1741-1747 DOI： 10.3788/OPE.20132107.1741.

摘要

针对上海光源X射线干涉光刻(XIL)光束线对狭缝精度的要求，提出了一种应用于超高真空的精密四刀狭缝机构及热缓释方案。给出了四刀狭缝机构的工作原理，其四个缝片独立运动，采用线性驱动装置及精密直线导轨来实现开合。根据XIL光束线的特点，设计了一种合理有效的热缓释方案，对缝片进行了热-结构耦合分析。对狭缝的精度指标进行了测试。结果显示：该四刀狭缝的分辨率优于0.1 m、运动重复精度优于2 m、刀口直线度优于2.5 m、平行度优于0.5 mrad，可以精确实现狭缝在水平和垂直方向-5～250 m的开度，缝片在热负载下的最大热变形控制在0.034 m。得到的结果表明，该精密四刀狭缝具有高的精度和稳定性，可满足XIL光束线的使用要求，现已实际使用并制备出了100 nm周期的刻蚀线结构。

Abstract

To meet the requirements of X-ray Inteferometric Lithography (XIL) beamline of Shanghai Synchrotron Radiation Facility for slit precision

an Ultra High Vacuum(UHV) four-knife precision slit structure and a cooling scheme were proposed. First

the structural principle of the four-knife precision slit structure was analyzed. The movements of the slits were controlled by linear drive devices independently

and their enclosures were achieved though the precision linear guides. Then

a cooling scheme was designed according to the characteristics of XIL beamline and the thermo-mechanical coupling was analyzed to verify whether the cooling scheme was reasonable. Furthermore

the precision indexes of slits were tested. The results indicate that the movement resolution and repeatability of the slit knife are better than 0.1 m and 2 m

respectively

the straightness and parallelism of the knife are better than 2.5 m and 0.5 mrad

respectively. It can also realize the opening of slits by only -5~250 m in both horizontal and vertical directions. Moreover

the maximum thermal deformation under the thermal load is controlled under 0.034 m. These results verify that the four-knife precision slit structure has a very high accuracy and stability

and meets the requirement of XIL beamline. By proposed slit structure and scheme

the etching line structure of 100 nm periodicity has been achieved.

关键词

Keywords

references

马礼敦.同步辐射装置-上海光源及其应用 [J]. 理化检验（物理分册）， 2009,45(11):717-723.MA D L. Sahnghai synnchrotron radiation facility and its application [J]. Physical testing and chemical analysis (Part A: Physical testing), 2009,45(11):717-723. (in Chinese)[2]吕清涛,薛松,彭忠琦,等.拉杆式压弯聚焦镜组件线性与接触非线性工程比较分析[J].光学精密工程,2010, 8(18):1843-1846.LV Q T，XUE S，PENG ZH Q, et al.. Comparison on linear and contact nonlinear analysis methods of pull-rod bent focusing mirror assembly [J]. Opt. Precision Eng., 2010,8(18):1843-1846. (in Chinese)[3]卢启鹏,高飒飒,彭忠琦. 同步辐射水平偏转压弯镜面形误差分析与补偿[J]. 光学精密工程, 2011, 11(19):2644-2650.LU Q P, GAO S S, PENG ZH Q. Slope error analysis and compensation for synchrotron radiation horizontal deflexed mirror [J]. Opt. Precision Eng., 2011,11(19):2644-2650. (in Chinese)[4]ANDREAS K F. Third-generation synchrotron radiation X-ray optics[J]. Facility. Stru., 1996, 4(2):121-125.[5]卢启鹏,马磊,彭忠琦.变包含角平面光栅单色器波长扫描机构转角精度的检测方法研究[J]. 光学精密工程, 2010,7(18):1548- 4553.LU Q P, MA L, PENG ZH Q. Rotation-angle-accuracy measurement of VAPGM wavelength scanning mechanism [J]. Opt. Precision Eng., 2010,7(18):1548-1553. (in Chinese)[6]徐朝银.同步辐射光学与工程（第三版）[M].合肥: 中国科学技术大学出版社, 2006,1-4, 105-111.XU CH Y. Synchrotron Radiation Optics and Engineering（The 3rd edition）[M]. Hefei: Publishing House of University of Science and Technology of China, 2006.14, 105111. (in Chinese)[7]赵高峰,薛松.新型柔性铰链式精密狭缝的结构原理及有限元分析[J]. 机械设计, 2009,11(26):21-23.ZHAO G F, XUE S. Structural principle and finite element analysis on new flexible hinged precision slit[J]. Journal of Machine Design, 2009,11(26):21-23. (in Chinese)[8]SHU D, BRITE C, NIAN T, et al.. Precision white beam slit design for high power density x-ray undulator beamlines at the Advanced Photon Source[J]. Rev. Sci. Instrum, 1995,66(2): 1789-1791.[9]王秋平,陈锵,余小江,等.新型精密狭缝的设计[J]. 航空精密制造技术, 2001,4(37),6-8.WANG Q P, CH Q, YU X J, et al.. A design of elastic-hinge-based precision slit mechanism [J]. Aviation Precision Manufactureing Technology, 2001,4(37),6-8. (in Chinese) [10]程琳,宋丽,马春桃.显微成像测量精密狭缝的重复精度[J]. 核技术, 2010,7(33):481-485.CHENG L, SONG L, MA CH T. High precision measurement of the micro-imaging system to check repeatability of precision optical slits in SSRF beamlines [J]. Nuclear Techniques, 2010,7(33):481-485. (in Chinese)[11]朱毅,夏绍建,王纳秀,等.上海光源插入件光束线白光狭缝设计[J]. 核技术, 2007, 6(30):481-485.ZHU Y, XIA SH J, WANG N X, et al.. The design of white beam slits for inset device beamlines of SSRF [J]. Nuclear Techniques, 2007,6(30):481-485. (in Chinese)[12]THOMAS N H L, KUZAY T M, SHU D, et al.. Thermo-mechanical analysis of the white beam slits for an undulator beamline at the advanced photon source[J]. Rev. Sci. Instrum, 1995,66(2): 1735- 1737.

浏览量

215

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

暂无数据