聚合物微结构热辅助超声波压印成形

罗怡; 闫旭; 陈莉; 王晓东

doi:10.3788/OPE.20142205.1220

您当前的位置：

首页 >

文章列表页 >

聚合物微结构热辅助超声波压印成形

微纳技术与精密机械 | 更新时间：2020-08-13

- 聚合物微结构热辅助超声波压印成形
- Replication of polymer microstructure using thermal-assisted ultrasonic embossing
- 光学精密工程 2014年22卷第5期页码：1220-1226
- 作者机构：
  
  大连理工大学辽宁省微纳米技术及系统重点实验室,辽宁大连,中国,116024
- 作者简介：
- 基金信息：
  
  国家自然科学基金资助项目（No.50975037）();国家973重点基础研究发展计划资助项目（No.2011CB013105）()
- DOI：10.3788/OPE.20142205.1220
  中图分类号： TB559;TH706
- 收稿日期：2013-12-01，
  
  修回日期：2014-02-15，
  
  纸质出版日期：2014-05-25
- 稿件说明：
移动端阅览
罗怡, 闫旭, 陈莉等. 聚合物微结构热辅助超声波压印成形[J]. 光学精密工程, 2014,22(5): 1220-1226

LUO Yi, YAN Xu, CHEN Li etc. Replication of polymer microstructure using thermal-assisted ultrasonic embossing[J]. Editorial Office of Optics and Precision Engineering, 2014,22(5): 1220-1226
罗怡, 闫旭, 陈莉等. 聚合物微结构热辅助超声波压印成形[J]. 光学精密工程, 2014,22(5): 1220-1226 DOI： 10.3788/OPE.20142205.1220.

LUO Yi, YAN Xu, CHEN Li etc. Replication of polymer microstructure using thermal-assisted ultrasonic embossing[J]. Editorial Office of Optics and Precision Engineering, 2014,22(5): 1220-1226 DOI： 10.3788/OPE.20142205.1220.

摘要

提出了基于硅模具的热辅助超声波压印成形方法，用于高效率、高精度地复制热塑性聚合物微结构。该方法利用作用于聚合物基片与模具间的超声波振动，快速升高界面温度，以达到聚合物的成形温度。为了降低破坏模具的风险，将模具预热到低于玻璃点转化温度（T

）以下35℃至50℃之后再施加超声波进行成形。最后，通过正交实验研究了超声振幅、超声波压力、超声波时间、热辅助温度以及聚合物基片厚度对压印结果的影响，揭示了超声波压印工艺的成形机理。实验结果表明，热辅助温度对压印影响最大，其次为超声波振幅，而超声波压力是影响复制均匀性的最重要的参数；薄的聚合物基片在同样的超声波参数和模具结构下更容易成形。通过优化参数，对聚甲基丙烯酸甲酯（PMMA）基片的深度复制精度达到了99%，复制周期小于50s。研究表明，热辅助超声波压印成形效率高，是一种具有批量制造潜力的聚合物微结构成形方法。

Abstract

A thermal-assisted ultrasonic embossing method was proposed based on silicon molds to replicate thermoplastic substrates in a low cost and high efficiency. The ultrasonic vibration was applied to the mold-polymer interface to heat the polymer rapidly to the embossing temperature. To reduce the risk of damaging the mold

the die was preheated to a temperature which is 35-50℃ below the glass transition temperature (T

) of the polymer. Then

the influences of the ultrasonic amplitude

ultrasonic force

ultrasonic time

and the thermal-assisted temperature were studied by orthogonal array experiments to reveal the mechanism of ultrasonic embossing. The influence of the substrate thickness was also investigated. The experimental results show that the most important parameter for replication is the thermal-assisted temperature

follows by the ultrasonic amplitude. Moreover

the ultrasonic force is the most important parameter for replication uniformity

while the thinner polymer sheets are more conducive to be replicated under the same circumstances. With the optimized parameters

the replication accuracy has reached 99% on a Polymethyl Methacrylate(PMMA) substrate

and the cycle time is less than 50 s. All theses studied show that thermal assisted ultrasonic embossing has high replication efficiency and is a potential way to mass formation of polymer microstructures.

关键词

Keywords

references

CHEN X, CUI D, ZHANG L.Portable fluorescence detection system integrated with isposable microfluidic chip [J].Nanotechnology and Precision Engineering, 2009, 7(2):127-131.

罗怡, 张苗苗, 孙屹博, 等. 面向聚合物微器件超声波精密封接的阵列微导能结构[J]. 光学精密工程, 2011, 19(4):754-761. LUO Y, ZHANG M M, SUN Y B, et al..Micro energy director array for ultrasonic precise sealing of polymer MEMS device [J].Opt.Precision Eng., 2011, 19(4):754-761.(in Chinese)

魏正英, 熊孝东, 杜军, 等. 常温微压印中抗蚀剂流动的研究及工艺优化[J]. 光学精密工程, 2010, 18(8):1822-1832. WEI Z Y, XIONG X D, DU J, et al..Flow behavior of resist in room-temperature micro-imprinting and its process optimization.Opt.Precision Eng., 2010, 18(8):1822-1832.(in Chinese)

CHOU S, KRAUSS P, RENSTROM P.Nanoimprint lithography [J].Journal of Vacuum Science and Technology B, 1996, 14(6):4129-4133.

祝铁丽, 周亮, 刘永云. 注射成形微流控芯片微沟槽成形质量的无损检测[J]. 光学精密工程, 2010, 18(7):1605-1612. ZHU T L, ZHOU L, LIU Y Y.Non-destructive testing for micro grooves of injection molded micro-fluidic chips [J].Opt.Precision Eng., 2010, 18(7):1615-1612.(in Chinese)

SHIH T, CHEN C, HO J, et al..Fabrication of PDMS(polydimethylsiloxane)microlens and diffuser using replica molding [J].Microelectronic Engineering, 2006, 83:11-12.

KOSTADINOV K, TRIFONOV D, Al-WAHAB M, et al..CD-based microfluidic device for automated immobilization and microinjection of biological cells [J].Micro and Nanosystems, 2011, 3:236-249.

WANG Y, HE Q, DONG Y, et al..In-channel modification of biosensor electrodes integrated on a polycarbonate microfluidic chip for micro flow-injection amperometric determination of glucose [J].Sensors and Actuators B:Chemical, 2010, 145:553-560.

LUO Y, WANG X, YANG F.Microfluidic chip made of COP(Cyclo-Olefin Polymer)and comparison to PMMA (Polymethylmeth-acrylate)microfluidic [J].Materials Processing Technology, 2008, 208:63-69.

MEKARU H, NOGUCHI T, GOTO H, et al..Nanoimprint lithography combined with ultrasonic vibration on polycarbonate [J].Japan Society of Applied Physics, 2007, 46:6355-6362.

YU H, SHIN B, LEE C, et al..Polymer microreplication using ultrasonic vibration energy [J].Micro/Nanolith MEMS MOEMS, 2009, 8(2), 021113.

LIU S, HUANG Y.Manufacture of dual-side surface-relief diffusers with various cross angles using ultrasonic embossing technique [J].Optics Express, 2009, 17(20):18083-18092.

LIN C, WANG C, CHEN R.Assisted-heating for ultrasonic nanoimprint lithography.Genoa, Italy IEEE Conference on Nanotechnology, 2009, 126-129.

浏览量

501

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

暂无数据