基于三维激光扫描的移动大尺寸圆柱体工件长度快速检测系统

周森; 郭永彩; 高潮; 吴小燕

doi:10.3788/OPE.20142206.1524

您当前的位置：

首页 >

文章列表页 >

基于三维激光扫描的移动大尺寸圆柱体工件长度快速检测系统

微纳技术与精密机械 | 更新时间：2020-08-13

- 基于三维激光扫描的移动大尺寸圆柱体工件长度快速检测系统
- Rapid length measuring system for mobile and large scale cylinder workpieces based on 3D laser scanning
- 光学精密工程 2014年22卷第6期页码：1524-1530
- 作者机构：
  
  重庆大学光电技术及系统教育部重点实验室重庆,400030
- 作者简介：
- 基金信息：
  
  教育部重点科研资助项目（No.1081741）();重庆市自然科学基金资助项目（No.CSTC.2008BB3169）()
- DOI：10.3788/OPE.20142206.1524
  中图分类号： TB92;TN247
- 收稿日期：2013-11-18，
  
  修回日期：2013-12-19，
  
  纸质出版日期：2014-06-25
- 稿件说明：
移动端阅览
周森, 郭永彩, 高潮等. 基于三维激光扫描的移动大尺寸圆柱体工件长度快速检测系统[J]. 光学精密工程, 2014,22(6): 1524-1530

ZHOU Sen, GUO Yong-cai, GAO Chao etc. Rapid length measuring system for mobile and large scale cylinder workpieces based on 3D laser scanning[J]. Editorial Office of Optics and Precision Engineering, 2014,22(6): 1524-1530
周森, 郭永彩, 高潮等. 基于三维激光扫描的移动大尺寸圆柱体工件长度快速检测系统[J]. 光学精密工程, 2014,22(6): 1524-1530 DOI： 10.3788/OPE.20142206.1524.

ZHOU Sen, GUO Yong-cai, GAO Chao etc. Rapid length measuring system for mobile and large scale cylinder workpieces based on 3D laser scanning[J]. Editorial Office of Optics and Precision Engineering, 2014,22(6): 1524-1530 DOI： 10.3788/OPE.20142206.1524.

摘要

针对移动大尺寸圆柱体工件两端的表面形貌特征，利用三维激光扫描仪设计了一种快速长度在线检测系统。基于三维激光扫描仪可在短时间内连续高速获取大量测量数据的特点，系统在虚拟环境下构造出自适应测量形状的虚拟测量基准面，采用二维误差分离方法抑制系统误差和运动误差，识别定位工件两端端点并计算其到虚拟测量基准面的位移；最后结合多传感器融合模型获取三维位移场测量结果。另外，测试前用三坐标测量机精密测量过的相似形状圆柱体工件对系统进行了校准修正。为验证系统的精度和可靠性，分别对处于（1 000±25）mm内不同直径的圆柱体工件进行了长度检测。结果显示，系统可在1 s完成直径约为50 mm工件的长度测量，检测分辨力为0.010 mm，检测精度达到0.050 mm。实际运行结果表明，该设计系统具有高自动性和高效性，可满足在线生产中对大尺寸工件控制和检测的要求。

Abstract

A novel rapid on-machine length measuring system based on 3D laser scanning was developed for mobile and large scale cylinder workpieces. By using the outstanding characters of laser scanners on fast continuously acquiring the mass of measurement points in a very short time

the multi-sensor fusion technique and a 2D error separation method were respectively introduced in this system in a virtual environment. Virtual measurement datum planes were established based on virtual registration sites

which followed the variant surface of measurement target. Then

the 3D displacement field measurements between end points and virtual measurement datum planes were built. A similar cylinder workpiece measured by Coordinate Measuring Machine (CMM ) was applied to calibration of the system. Finally

the experiments on the cylinder workpieces (1 000±25) mm with different diameters were carried out to determine the accuracy and reliability of measuring system. The experimental results indicate that a workpiece with a diameter about 50 mm is perfectly measured in only 1 s with the resolution less than 0.010 mm and the measuring precision over 0.050 mm. According to the actual operation results

this proposed measuring system is characterized by high automation and high efficiency

and can be well acceptable for application as online length detection for large scale workpieces in industrial production.

关键词

Keywords

references

DENNIS A S. Length and dimensional measurements at NIST[J]. Journal of Research of the National Institute of Standards and Technology, 2001, 106(1): 1-23.

ESTLER W T, EDMUNDSON K L, PEGGS G N, et al.. Large- scale metrology an update [J]. CIRP Annals-Manufacturing Technology, 2002, 51(2): 587-609.

张福民, 曲兴华, 叶声华. 大尺寸测量中多传感器的融合[J]. 光学精密工程, 2008, 16(7): 1237-1240. ZHANG F M, QU X H, YE SH H. Multiple sensor fusion in large scale measurement [J]. Opt. Precision Eng., 2008, 16(7):1237-1240. (in Chinese)

刘建伟, 梁晋, 梁新合. 大尺寸工业视觉测量系统[J]. 光学精密工程, 2010, 18(1): 126-134. LIU J W, LIANG J, LIANG X H. Industrial vision measuring system for large dimension work-pieces[J]. Opt. Precision Eng., 2010,18(1):126-134. (In Chinese)

WECKENMANN A, ESTLER T, PEGGS G, et al.. Probing systems in dimensional metrology [J]. CIRP Annals-Manufacturing Technology, 2004, 53(2): 657-684.

裘祖荣, 石照耀, 李岩. 机械制造领域测量技术的发展研究[J]. 机械工程学报, 2010, 46(14):1-11. QIU Z R, SHI ZH Y,LI Y. Research on the development of measurement technology mechanical manufacture [J]. Mechanical Engineering, 2010, 46(14):1-11. (in Chinese)

LSHEIL A, GONNET J P, JOANNIC D,et al.. Systematic error correction of a 3D laser scanning measurement device [J]. Optics and Laser in Engineering, 2011, 49:16-24.

ZHAO H B, JEAN P K, NICK V G, et al. Automated dimensional inspection planning using the combination of laser scanner and tactile probe [J]. Measurement, 2012, 45: 1057-1066.

MAILHE J,LINARES J M. Geometrical checking by virtual gauge, including measurement uncertainties[J]. CIRP Annals-Manufacturing Technology, 2008, 57: 513-516.

ZHU SH P,FANG J CH,ZHOU R. A new noncontact flatness measuring system of large 2-D flat workpiece [J]. IEEE Transactions on instrumentation and measurement, 2008, 12(57): 2891-2904.

JUNG C L, GAO W, YUKI S, et al.. Precision measurement of carriage slide motion error of a drum roll lathe [J]. Precision Engineering, 2012, 36: 244-251.

GAO W, SATO SHI KIYONO. High accuracy profile measurement of a machined surface by the combined method [J]. Measurement, 1996, 19(1):55-64.

EIKI O. Multi-probe method for straightness profile measurement based on least uncertainty propagation (1st report)[J]. Precision Engineering, 2010, 34: 49-54.

NICK V G, STEVEN C, PHILIP B,et al.. A performance evaluation test for laser line scanners on CMMs [J]. Optics and Laser in Engineering, 2009, 47:336-342.

刘万里, 曲兴华, 欧阳健飞, 等. 激光跟踪测量系统角度自动校正装置设计[J]. 光学精密工程, 2008, 16(9):1696-1700. LIU W L, QU X H, OU YANG J F, et al.. Design of angular automatic calibration mechanism for laser tracker system[J]. Opt. Precision Eng., 2008, 16(9):1696-1700. (in Chinese)

浏览量

208

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

用于大尺寸工件的动态长度测量系统

局部相关点平衡的三维激光点云骨架提取

基于激光扫描的密集泡状流三维重建与优化

基于激光扫描技术的采煤机精确定位系统

痕量微生物快速检测系统