激光冲击强化对TiAl合金组织和性能的影响

乔红超; 赵亦翔; 赵吉宾; 陆莹

doi:10.3788/OPE.20142207.1766

您当前的位置：

首页 >

文章列表页 >

激光冲击强化对TiAl合金组织和性能的影响

现代应用光学 | 更新时间：2020-08-13

- 激光冲击强化对TiAl合金组织和性能的影响
- Effect of laser peening on microstructures and properties of TiAl alloy
- 光学精密工程 2014年22卷第7期页码：1766-1773
- 作者机构：
  
  1. 中国科学院沈阳自动化研究所,辽宁沈阳,110016
  2. 中国科学院金属研究所,辽宁沈阳,110016
- 作者简介：
- 基金信息：
  
  国家863高技术研究发展计划资助项目（No.2012AA041310）()
- DOI：10.3788/OPE.20142207.1766
  中图分类号： TG665;TG146.2
- 收稿日期：2013-09-04，
  
  修回日期：2013-11-04，
  
  纸质出版日期：2014-07-25
- 稿件说明：
移动端阅览
乔红超, 赵亦翔, 赵吉宾等. 激光冲击强化对TiAl合金组织和性能的影响[J]. 光学精密工程, 2014,22(7): 1766-1773

QIAO Hong-chao, ZHAO Yi-xiang, ZHAO Ji-bin etc. Effect of laser peening on microstructures and properties of TiAl alloy[J]. Editorial Office of Optics and Precision Engineering, 2014,22(7): 1766-1773
乔红超, 赵亦翔, 赵吉宾等. 激光冲击强化对TiAl合金组织和性能的影响[J]. 光学精密工程, 2014,22(7): 1766-1773 DOI： 10.3788/OPE.20142207.1766.

QIAO Hong-chao, ZHAO Yi-xiang, ZHAO Ji-bin etc. Effect of laser peening on microstructures and properties of TiAl alloy[J]. Editorial Office of Optics and Precision Engineering, 2014,22(7): 1766-1773 DOI： 10.3788/OPE.20142207.1766.

摘要

为研究激光冲击强化对TiAl合金组织和性能的影响，利用波长为1 064 nm、脉宽为20 ns、单脉冲能量为0~22 J的Nd：YAG激光器对TiAl合金试件进行了实验研究。采用显微硬度计、表面粗糙度仪和扫描电镜分别测量了激光冲击强化前后的表面显微硬度、粗糙度和表面微观形貌，利用X射线应力分析仪测量了激光冲击强化表面残余应力和晶面极性，并分析了其高温稳定性。实验结果表明：当单脉冲能量增加到9 J时，表面显微硬度增加了33.4%，粗糙度由0.042 μm增大到了0.285 μm，表面残余压应力由20 MPa增加到了297 MPa，表面微观形貌出现了凸凹不平，局部纹理和层状微结构。将9 J激光冲击强化后的试件在650℃下保温4 h后，残余压应力值从297 MPa降到230 MPa，显微硬度值从377 HV

0.2

降到345 HV

0.2

，（002）晶面取向有向中心移回的趋势。得到的数据显示，激光冲击强化能够极大地改善TiAl合金的组织和性能，且具有一定的高温稳定性。

Abstract

To study the effect of laser peening on microstructures and properties of TiAl alloy

TiAl alloy samples were treated by a Nd:YAG laser system with a wavelength of 1 064 nm

a pulse-width of 20 ns

and a pulse-energy of range 0-22 J.The surface micro-hardness

roughness

and microstructural characteristics of the samples before and after laser peening were tested with a micro-hardness tester

a roughness tester and a Scanning Electron Microscope (SEM).The residual stress and pole figures of TiAl alloy were tested with X-ray Diffraction (XRD) and their high-temperature stabilities were analyzed.The experimental results show that the surface micro-hardness increases up to 33.4%

the roughness increases from 0.042 μm to 0.285 μm

the compress residual stress increases from 20 MPa to 297 MPa with the pulse energy up to 9 J

and the local textures and typical lamellar microstructures are generated.When the samples are heated for 4 h at 650℃

the residual stress value and micro hardness values have droped from 297 MPa to 230 MPa

and 377 HV

0.2

to 345HV

0.2

respectively

and the (002) poles shift back to the center slightly.It concludes that the laser peening improves microstructures and properties of TiAl alloy significantly.

关键词

Keywords

references

周建忠,卫登辉,黄舒,等. 微尺度激光喷丸强化TiN涂层的表面性能[J]. 光学精密工程,2011,19(11):2679-2684. ZHOU J ZH,WEI D H,HUANG SH,et al. Microscale laser shock peening on TiN coatings[J]. Opt. Precision Eng. ,2011,19(11):2679-2684. (in Chinese)

陶春虎,刘庆瑔,曹春晓,等. 航空用钛合金的失效及其预防[M]. 北京:国防工业出版社,2002:5-10. TAO CH H,LIU Q Q,CAO CH X,et al. Aerospace titanium alloys failure and its prevention[M]. Beijing:National Defense Industry Press,2002:5-10. (in Chinese)

乔红超,赵吉宾,陆莹. 纳秒脉宽Nd:YAG激光冲击强化激光器的研制及分析[J]. 中国激光,2013,40(8):08020011-08020017. QIAO H CH,ZHAO J B,LU Y. Develop and analysis of nanosecond pulse width Nd:YAG laser for laser peening[J]. Chinese Journal of Lasers,2013,40(8):08020011-08020017. (in Chinese)

冯德军,黄文育,纪鹏宇,等. 基于石墨烯可饱和吸收体的掺铒光纤环形腔脉冲激光器[J]. 光学精密工程,2013,21(5):1097-1101. FENG D J,HUANG W Y,JI P Y,et al. Erbium-doped fiber ring cavity pulsed laser based on grapheme saturable absorber[J]. Opt. Precision Eng. ,2013,21(5):1097-1101. (in Chinese)

王加贤,林正怀,张培,等. 纳米半导体复合薄膜的非线性光学性质及其在激光器中的应用[J]. 光学精密工程,2013,21(1):20-25. WANG J X,LIN ZH H,ZHANG P,et al. Nonlinear optical properties of nanometer semiconductor compound films and their applications to lasers[J]. Opt. Precision Eng. ,2013,21(1):20-25. (in Chinese)

张晓伟,刘洪喜,蒋业华,等. 激光原位合成TiN/Ti3Al基复合涂层[J]. 金属学报,2011,47(8):1086-1093. ZHANG X W,LIU H X,JIANG Y H,et al. Laser in situ synthesized TiN/Ti3Al composite coatings[J]. Acta Metallurgica Sinica,2011,47 (8):1086-1093. (in Chinese)

LIU X D,SHANG D G,LI M,et al. Healing fatigue damage by laser shock peening for copper film[J]. International Journal of Fatigue,2013,54:127-132.

VASU A,GRANDHI R V. Effect of curved geometry on residual stress in laser peening[J]. Surface and Coating Technology,2013,218(1):71-79.

静永娟,王新英,张继. 喷丸处理对TiAl合金拉伸性能的影响[J]. 稀有金属,2009,33(5):750-753. JING Y J,WANG X Y,ZHANG J. Effect of shot peening on tensile properties of TiAl alloys[J]. Chinese Journal of Fare Metals,2009,33(5):750-753. (in Chinese)

CHAI L H,CHEN Y Y,ZHANG L Q,et al. Effect of spark plasma sintering temperature on microstructure and mechanical properties of melt-spun TiAl alloys[J]. Trans. Nonferrous Met. Soc. China,2012,22(3):528-533.

APPEL F,HERRMANN D,FISCHER F D,et al. Role of vacancies in work hardening and fatigue of TiAl alloys[J]. Inter. Jour. Plasticity,2013,42:83-533.

陈国琳,吴鹏炜,冷文军,等. 钛合金的发展现状及应用前景[J]. 舰船科学技术,2009,42 (12):110-113. CHEN G L,WU P W,LENG W J,et al. The development prospect and current status of titanium alloys[J]. Ship Science and Technology,2009,42(12):110-113. (in Chinese)

LIU K K,HILL M R. The effects of laser peening and shot peening on fretting fatigue in Ti-6Al-4V coupons[J]. Tropology International,2009,42:1250-1262.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

暂无数据