4mSiC轻量化主镜的主动支撑系统

吴小霞; 李剑锋; 宋淑梅; 邵亮; 明名

doi:10.3788/OPE.20142209.2451

您当前的位置：

首页 >

文章列表页 >

4mSiC轻量化主镜的主动支撑系统

微纳技术与精密机械 | 更新时间：2020-08-13

- 4mSiC轻量化主镜的主动支撑系统
- Active support system for 4 m SiC lightweight primary mirror
- 光学精密工程 2014年22卷第9期页码：2451-2457
- 作者机构：
  
  中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
- 作者简介：
- 基金信息：
  
  中科院长春光学精密机械与物理研究所重大创新项目专项基金资助项目（No.Y3C122E130）()
- DOI：10.3788/OPE.20142209.2451
  中图分类号： TH751
- 收稿日期：2014-01-20，
  
  修回日期：2014-02-27，
  
  纸质出版日期：2014-09-25
- 稿件说明：
移动端阅览
吴小霞, 李剑锋, 宋淑梅等. 4mSiC轻量化主镜的主动支撑系统[J]. 光学精密工程, 2014,22(9): 2451-2457

WU Xiao-xia, LI Jian-feng, SONG Shu-mei etc. Active support system for 4 m SiC lightweight primary mirror[J]. Editorial Office of Optics and Precision Engineering, 2014,22(9): 2451-2457
吴小霞, 李剑锋, 宋淑梅等. 4mSiC轻量化主镜的主动支撑系统[J]. 光学精密工程, 2014,22(9): 2451-2457 DOI： 10.3788/OPE.20142209.2451.

WU Xiao-xia, LI Jian-feng, SONG Shu-mei etc. Active support system for 4 m SiC lightweight primary mirror[J]. Editorial Office of Optics and Precision Engineering, 2014,22(9): 2451-2457 DOI： 10.3788/OPE.20142209.2451.

摘要

针对4 m光电望远镜中SiC轻量化主镜比刚度大，面形精度要求高的特点，提出采用液压whiffletree被动支撑并联力促动器主动支撑的轴向液压主动支撑方案。液压被动支撑承担镜重，主动支撑仅输出校正主镜面形误差所需的主动校正力，从而减小主动支撑元件力促动器的作用力范围，提高主动校正力精度。借助于有限元法完成了轴向和侧向支撑系统的优化，确定了轴向54点和侧向24点等间距等力（

=0.5）支撑系统设计。当仅有被动支撑作用时，主镜水平和竖直状态下重力引起的镜面变形误差RMS值分别为37.8 nm和82.9 nm。采用主动校正后，主镜水平和竖直状态下的镜面变形误差RMS分别减小到12.0 nm和9.8 nm。不同俯仰角下主镜的镜面变形均能满足面形误差RMS不大于

/30（

=632.8 nm）的指标要求。

Abstract

As the SiC lightweight primary mirror in a 4 m photoelectric telescope has high specific stiffness and needs strict surface precision

this paper proposes an axial active support system based on the hydraulic whiffletree passive support for the primary mirror. The hydraulic whiffletree support system was used to support the mirror weight

and the active support was just output active forces to correct mirror surface errors

reduce the active force range and to increase the precision of active force. A 54-point axial support system and a 24-point lateral support system were optimized by the Finite Element Method(FEM)

and the parameter of lateral force

was 0.5. With the hydraulic passive support system

the mirror surface deformation Root Mean Square(RMS) values from the gravity of the primary mirror are 37.8 nm and 82.9 nm respectively under horizontal and vertical states. After active correction

the mirror surface error RMS values are reduced to 12.0 nm and 9.8 nm accordingly. Analysis indicates that the mirror surface deformation of 4 m SiC lightweight primary mirror at different pitch angles is less than

/30(

=632.8 nm) and meets the requirements of surface errors.

关键词

Keywords

references

IWONA A P, ISAAC G. Developing SiC for optical system applications [J]. SPIE, 2004, 5524: 14-20.

WILSON R N. The history and development of the ESO active optics system [J]. Telescope and instrumentation, September, 2003: 2-9.

NOETHE L, ANDREONI G, FRANZA F, et al.. Latest developments of active optics of the ESO NTT and the implication for the ESO VLT [J]. SPIE, 1991, 1542: 293-296.

JAMES E, KIMBRELL, DAVID G, et al.. AEOS 3.67 m telescope primary mirror active control system[J]. SPIE, 1998, 3352:400-411.

VICTOR L. Krabbendam. active optical system design for 4.2 m SOAR telescope [J]. SPIE, 2000, 4003:122-135.

LARRY STEPP, EUGENE HUANG. Gemini primary mirror support system [J]. SPIE, 1994, 2199: 223-238.

MARTIN H M, ALLEN R G, CUERDEN B, et al.. Primary mirror system for the first Magellan telescope [J]. SPIE, 2000, 4003: 2-13.

MARTIN H M, CALLAHAN S P, CUERDEN B, et al.. Active support and force optimization for the MMT primary mirror [J]. SPIE, 1998, 3352:412-423.

MARTIN H M, CUERDEN B, DETTMANN L R, et al.. Active optics and force optimization for the first 8.4m LBT mirror [J]. SPIE, 2004, 5489:826-837.

陈夫林,张景旭,吴小霞,等. 620 mm薄镜面的主动支撑结构及面形校正[J]. 光学精密工程, 2011, 19(5): 1022-1029. CHEN F L, ZHANG J X, WU X X, et al.. Supporting structure of 620 mm thin primary mirror and its active surface correction [J]. Opt. Precision Eng., 2011, 19(5): 1022-1029. (in Chinese)

张玉芳,李国平. 用于薄镜面主动光学的音圈力促动器设计[J]. 光学精密工程, 2013, 21 (11): 2836-2842. ZHANG Y F, LI G P. Design of voice coil force actuator in thin mirror active optical system [J]. Opt. Precision Eng., 2013, 21 (11): 2836-2842. (in Chinese)

SU D Q, JIANG SH T, ZOU W Y, et al..Experiment system of thin-mirror active optics [J]. SPIE, 1994, 2199:609-621.

范磊,张景旭,邵亮,等. 采用液压Whiffle-tree的大口径主镜轴向支撑[J]. 红外与激光工程, 2013, 42(8): 2126-2131. FAN L, ZHANG J X, SHAO L, et al.. Axial support for large aperture primary mirror based on hydraulic whiffletree [J]. Infrared and Laser Engineering, 2013, 42(8): 2126-2131. (in Chinese)

张舸. 1.5 m量级SiC陶瓷素坯凝胶注模成型工艺[J]. 光学精密工程, 2013, 21 (12): 2989-2993. ZHANG G. Gelcasting process of 1.5 m SiC Ceramic green body [J]. Opt. Precision Eng., 2013, 21 (12): 2989-2993. (in Chinese)

徐宏,关英俊. 空间相机1 m口径反射镜组件结构设计[J]. 光学精密工程, 2013, 21 (6): 1488-1495. XU H, GUAN Y J. Structural design of 1m diameter space mirror component of space camera [J]. Opt. Precision Eng., 2013, 21 (6): 1488-1495. (in Chinese)

伞晓刚, 孙宁, 卓仁善, 等. 大口径光电经纬仪主反射镜支撑结构设计[J]. 光学精密工程, 2013, 21 (12): 3111-3117. SAN X G, SUN N, ZHAO R SH, et al.. Design of supporting structure for primary mirror of large aperture theodolite [J]. Opt. Precision Eng., 2013, 21 (12): 3111-3117. (in Chinese)

邵亮, 杨飞, 王富国, 等. 1.2 m轻量化SiC主镜支撑系统优化设计[J]. 中国光学, 2012, 5 (3): 229-234. SHAO L, YANG F, WNAG F G, et al.. Design and optimization of supporting system for 1.2 m lightweight SiC primary mirror [J]. Chinese Optics, 2012, 5 (3): 229-234. (in Chinese)

陈伟, 丁亚林, 惠守文, 等. 碳化硅扫描反射镜支撑结构设计[J]. 中国光学, 2012, 5 (2): 161-166. CHEN W, DING Y L, HUI SH W, et al.. Design of kinematic mount for SiC Scanning reflective mirror [J]. Chinese Optics, 2012, 5 (2):161-166. (in Chinese)

叶伟楠, 董吉洪. 大口径主镜轻量化结构参数的优化设计[J]. 中国光学, 2012, 5 (3): 222-228. YE W N, DONG J H. Optimized design of lightweight structural parameters for large-aperture primary mirror [J]. Chinese Optics, 2012, 5 (3): 222-228. (in Chinese)

康健, 宣斌, 谢京江. 表面改性碳化硅基底反射镜加工技术现状[J]. 中国光学, 2013, 6(6): 824-833. KANG J, XUAN B, XIE J J. Manufacture technology status of surface modified silicon carbide mirrors [J]. Chinese Optics, 2013, 6(6): 824-833. (in Chinese)

陈宝刚, 明名, 吕天宇. 大口径球面反射镜曲率半径的精确测量[J]. 中国光学, 2014, 7(1): 163-168. CHEN B G, MING M, LV T Y. Precise measurement of curvature radius for spherical mirror with large aperture [J]. Chinese Optics, 2014, 7(1): 163-168. (in Chinese)

杨飞, 安其昌, 张景旭. 基于功率谱的反射镜面形评价[J]. 中国光学, 2014, 7(1): 156-162. YANG F, AN Q CH, ZHANG J X. Mirror surface figure evaluation based on power spectral density [J]. Chinese Optics, 2014, 7(1): 156-162. (in Chinese)

李剑锋. 望远镜主动支撑用液压缸设计研究[J]. 长春理工大学学报:自然科学版, 2013, 36(3-4): 75-80. LI J F. Research on the design of cylinder used as the primary mirror support of telescope [J]. Journal of Changchun University of Science and Technology (Natural Science Edition), 2013, 36(3-4): 75-80. (in Chinese)

苏定强, 崔向群. 主动光学——新一代大望远镜的关键技术[J]. 天文学进展, 1999, 17(1): 1-14. SU D Q, CUI X Q. Active optics-key technology of the new generation telescope [J]. Progress in astronomy, 1999, 17(1): 1-14. (in Chinese)

浏览量

383

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

SiC轻量化主镜的被动支撑系统