空间长条形反射镜背部三支撑点的设置

朱俊青; 沙巍; 陈长征; 张星祥; 任建岳

doi:10.3788/OPE.20152309.2562

您当前的位置：

首页 >

文章列表页 >

空间长条形反射镜背部三支撑点的设置

微纳技术与精密机械 | 更新时间：2020-08-12

- 空间长条形反射镜背部三支撑点的设置
- Position layout of rear three point mounting for space rectangular mirror
- 光学精密工程 2015年23卷第9期页码：2562-2569
- 作者机构：
  
  1. 中国科学院长春光学精密机械与物理研究所,吉林长春,中国,130033
  2. 中国科学院大学北京,中国,100049
- 作者简介：
- 基金信息：
  
  国家863高技术研究发展计划资助项目(No.863-2-5-1-13B)()
- DOI：10.3788/OPE.20152309.2562
  中图分类号： TH703;TH743
- 收稿日期：2014-12-11，
  
  修回日期：2015-01-20，
  
  纸质出版日期：2015-09-25
- 稿件说明：
移动端阅览
朱俊青, 沙巍, 陈长征等. 空间长条形反射镜背部三支撑点的设置[J]. 光学精密工程, 2015,23(9): 2562-2569

ZHU Jun-qing, SHA Wei, CHEN Chang-zheng etc. Position layout of rear three point mounting for space rectangular mirror[J]. Editorial Office of Optics and Precision Engineering, 2015,23(9): 2562-2569
朱俊青, 沙巍, 陈长征等. 空间长条形反射镜背部三支撑点的设置[J]. 光学精密工程, 2015,23(9): 2562-2569 DOI： 10.3788/OPE.20152309.2562.

ZHU Jun-qing, SHA Wei, CHEN Chang-zheng etc. Position layout of rear three point mounting for space rectangular mirror[J]. Editorial Office of Optics and Precision Engineering, 2015,23(9): 2562-2569 DOI： 10.3788/OPE.20152309.2562.

摘要

采用背部三点支撑方式的空间光学遥感器长条形反射镜目前尚无普遍适用的支撑点设置方法

只能对某一确定尺寸和长宽比的反射镜进行专门设计。本文提出了基于规则模型的、以参数化模型为核心的集成参数化设计方法

并建立了长条形实体反射镜背部三点支撑集成参数化模型。在集成环境中通过试验设计、响应面分析等方法对设计参数进行了分析和优化

结果表明在轴向重力工况

镜面面形峰谷(PV)值优于

/10 (

=632.5 nm)的设计要求下

长条形碳化硅反射镜背部三点支撑的最大适用尺寸为1 m。文中给出了最优支撑点布置

并确定了厚径比最优为1/10。最后

对集成参数化分析方法进行了精度分析

结果显示该方法整体误差为6.13%。提出的方法确定了空间长条镜背部三点支撑的适用范围

提供了支撑点最佳布置

为空间相机不同尺寸要求的长条镜设计打下了基础。

Abstract

It is difficult to conclude a general method in opto-mechanical design for rectangular mirrors mounted via rear three-point method in a space remote sensor. So

the individual opto-mechanical design for a given size rectangular mirror is usually used. In this paper

an integrated parametric design method based on a regular model was proposed and a parametric model for 3-point mounting space rectangular mirror was established. Integrated analysis and response surface method were used in analysis and optimization of the designed parameters. The results show that the size limit of mirror for rear three mounting method is 1 m for the requirement of the axial self-weight deflection of wavefront error less than 1/10

(

=632.5 nm). The best mounting position was proposed

and the proper thick aspect ratio was given by 1/10. The accuracy of the proposed integrated parametric design method was analyzed

and the results show that the total analysis error is 6.13%. The method defines the proper size of rectangular mirror with rear three point mounting

gives the best mounting position and provides a standard for design of space remote sensors.

关键词

Keywords

references

严从林,吴钦章,刘卫林. 大型矩形反射镜支撑结构设计[J]. 光电工程, 2013,40(3):135-141. YAN C L, WU Q ZH, LIU W L. Design and analysis for the support of large aperture rectangular mirror [J]. Opto-Electronic Engineering, 2013, 40(3):135-141. (in Chinese)

刘巨,董得义,辛宏伟,等. 大口径反射镜组件的温度适应性[J]. 光学精密工程,2013(12):3169-3175. LIU J, DONG D Y, XIN H W, et al.. Temperature adaptation of large aperture mirror assembly [J]. Opt. Precision Eng., 2013(12):3169-3175.(in Chinese)

徐宏,关英俊. 空间相机1 m口径反射镜组件结构设计[J]. 光学精密工程,2013(6):1488-1495. XU H, GUAN Y J. Structural design of 1 m diameter space mirror component of space camera [J]. Opt. Precision Eng., 2013(6):1488-1495.(in Chinese)

沙巍,陈长征,张星祥,等. 空间反射镜轻量化结构的拓扑优化设计[J]. 光电工程, 2009, 36(4):35-39. SHA W, CHEN CH ZH, ZHANG X X, et al.. Topological lightweight design of space mirror [J]. Opto-Electronic Engineering, 2009, 36(4):35-39.(in Chinese)

刘书田,胡瑞,周平,等. 基于筋板式基结构的大口径空间反射镜构型设计的拓扑优化方法[J]. 光学精密工程, 2013,21(7):1803-1810. LIU SH T, HU R, ZHOU P, et al.. Topologic optimization for configuration design of web-skin-type ground structure based large aperture space mirror [J]. Opt. Precision Eng.,2013,21(7):1803-1810.(in Chinese)

PAUL R Y J.Opto-mechanical Systems Design (third edition)[M]. Boca Raton:CRC Press, 2008:503-506.

MICHELS G J, GENBERG V L, DOYLE K B, et al.. Design optimization of actuator layouts of adaptive optics using a genetic algorithm [C].Optics & Photonics 2005. International Society for Optics and Photonics, 2005:58770L-58770L-9.

COHAN L E, MILLER D W. Integrated modeling for determining launch survival and limitations of actuated, lightweight mirrors [C]. Proc. SPIE., 2008, 7010:70102I.

伞晓刚,孙宁,卓仁善,等. 大口径光电经纬仪主反射镜支撑结构设计[J]. 光学精密工程,2013,21(12):3111-3117. SAN X G, SUN N, ZHUO R SH, et al.. Design of supporting structure for primary mirror of large aperture theodolite [J]. Opt. Precision Eng., 2013,21(12):3111-3117.(in Chinese)

GERSH-RANGE J A, ARNOLD W R, PECK M A, et al.. A parametric finite-element model for evaluating segmented mirrors with discrete edgewise connectivity [C]. SPIE Optical Engineering Applications. International Society for Optics and Photonics, 2011:81250H-81250H-9.

张舸. 1.5 m量级SiC陶瓷素坯凝胶注模成型工艺[J]. 光学精密工程,2013,21(12):2989-2993. ZHANG G. Gelcasting process of 1.5 m SiC ceramic green body [J]. Opt. Precision Eng.,2013,21(12):2989-2993.(in Chinese)

ANDERSON-COOK C M. Response Surface Methodology:Process and Product Optimization Using Designed Experiments [M]. US:John Wiley & Sons, 2009:34:102.

王书新. 2 m量级空间反射镜组件设计与优化[D]. 北京:中国科学院研究生院, 2013. WANG SH X. Design and Optimization of 2 m-Class Space Reflector Assemblies [D]. Beijing:Graduate University of the Chinese Academy of Sciences, 2013.(in Chinese)

浏览量

681

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

大口径长条形反射镜组件自重变形的仿真与试验

应用旋转法实现大口径非球面反射镜零重力面形加工

机载光谱仪高模态主支撑结构优化设计

机载光谱仪高模态主支撑结构优化

大口径空间反射镜大容差支撑结构设计与优化